Servis-Rhino RC-12 manual Brake and Differential Lock Setting, Raising the Mower

Page 62

OPERATION

OPERATION

9.2 Brake and Differential Lock Setting

Make sure the tractor brakes are in good operating condition. Tractor brakes can be set to operate independently allowing single rear wheel braking action or locked together to provide simultaneous rear wheel braking. FOR MOST DRIVING AND OPERATING CONDITIONS, THE BRAKE PEDALS SHOULD BE LOCKED TOGETHER TO PROVIDE THE MOST EFFECTIVE BRAKING ACTION.

Always disengage the tractor differential lock when turning. When engaged the differential lock will prevent or limit the tractor from turning. During normal cutting conditions, locking the differential provides no benefit and should not be used. OPS- U- 0013

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes. When operating down a hill or on wet or rain slick roads, the braking distance increases; use extreme care and reduce your speed in these conditions. When operating in traffic, always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy.

9.3 Raising the Mower

Using the tractor 3-point hitch control lever, raise the mower off the ground about 6”, or just high enough to clear any ground obstacles. When raising the mower, make sure all connection points are securely attached and at least 1” clearance is maintained between the driveline and the deck. If necessary, place an upper lift strip on the 3-point hitch control lever to limit the height the mower can be raised to avoid driveline damage.

RC12 12/05

Operation Section 4-20

© 2005 Alamo Group Inc.

Image 62
Contents RC-12 Warranty Information To the Owner/Operator/DealerTable of Contents Maintenance Section Safety Section Safety Wait a minute...Save a life Safety Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards Unless Safety Safety RC12 Safety Section STI-3 Safety MPH. STI-6 Maintenance and Service Safety Instructions and Practices Parts Information Concluding Safety Instructions and Practices Instruct PeligroReflect Name NFS SER PLTLogo ModelDecal Description Has stopped. P/N RC12 Safety Section Safety Safety Safety Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction Before Operating this Machine Owners Responsibilities Safety Instructions Page Assembly Section Shipping Stand Removal Breather Plug InstallationTongue Assembly Installation Assembly Asm-FL-0066 Point Hitch Assembly Installation Attaching Axle Assemblies to Main Wheel BAR Tube Attaching Optional Hydraulic CylinderOperation Section Operation Operation CAT II-III Q.HOperator Requirements Personal Protective Equipment PPERops and Seat Belt Tractor Safety DevicesTractor Requirements and Capabilities 3-Point Hitch Front End WeightPower Take Off PTO Drawbar-Pull Type MowerGetting on and OFF the Tractor Boarding the TractorDismounting the Tractor Connecting the Mower to the Tractor Starting the TractorLift Type Models Setting the MowerPull Type Models Semi-Mount ModelsOperation Driveline Attachment Leveling DeckDriveline Clearance Shorten the driveline profiles as follows PRE-OPERATION Inspection and ServiceEngagement Check Procedure Tractor Pre-Operation Inspection/Service Mower Pre-Operation Inspection/ServiceSGM-10 Operation Driving the Tractor and Implement Starting the Tractor Brake and Differential Lock Setting Raising the MowerTurning Procedure Driving the Tractor and MowerCrossing Ditches and Steep Inclines Operating the Tractor and Implement Operation Bystanders/Passersby Precautions Foreign Debris HazardsEngaging the Power Take Off PTO PTO RPM and Ground Speed Operating the MowerOperation Shutting Down the Implement Disconnecting the Mower from the Tractor OPS-F-0012AMower Storage Transporting the Tractor and ImplementOperation Transporting on Public Roadways OPS-U Hauling the Tractor and Implement Trouble Shooting Guide Problem Possible Cause RemedyPTO RPM Page Maintenance Section General Maintenance LubricationRoutine Maintenance Cutter Shaft Blade ReplacementBelt Adjustment and Replacement Pulley Alignment and Removal Maintenance Cutter Shaft Bearing Removal Mnt-FL-0041 InstallationCutter Shaft and Bearing Removal Outer Cutter Shaft Bearing RemovalTOP Drive Assembly Servicing Cutter Shaft RemovalMnt-FL-0032 Driveline Shield ReplacementDriveline Figure Mnt-FL-0036 Storing the RC12 Pre-season CheckRhino Required of the Owner Required of the OperatorRC12 12/05 00726339C Printed U.S.A