Servis-Rhino RC-12 manual Operation

Page 59

OPERATION

Ensure rubber deflectors are in position and not damaged. Replace worn, broken, and missing sections immediately.

Ensure the rollers are in good condition and rotate freely.

Ensure the driveline integral shield is in good condition and rotate freely.

Inspect that all bolts and screws are in position and are properly torqued. OPS-F- 0004

Inspect the condition of the drive belts.

Ensure the slip clutch (rear mower section only) is properly adjusted and the friction plates are not frozen together. Reference the Maintenance Section for proper slip clutch maintenance.

Ensure the slop clutch shield and drive belts shields are in place and in good repair.

Ensure the tractor PTO master shield is in place, lowered and in good condition. OPS-F- 0016

.Inspect oil level in gearbox and replenish if needed. A low oil level is a warning sign that the gearbox may be cracked or its seal is damaged and needs to be replaced.

Perform scheduled lubrication as specified in the maintenance section. OPS-F- 0017

RC12 12/05

Operation Section 4-17

© 2005 Alamo Group Inc.

OPERATION

Image 59
Contents RC-12 To the Owner/Operator/Dealer Warranty InformationTable of Contents Maintenance Section Safety Section Safety Wait a minute...Save a life Safety Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards Unless Safety Safety RC12 Safety Section STI-3 Safety MPH. STI-6 Maintenance and Service Safety Instructions and Practices Parts Information Concluding Safety Instructions and Practices Instruct PeligroReflect Model NFS SER PLTLogo NameDecal Description Has stopped. P/N RC12 Safety Section Safety Safety Safety Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction Before Operating this Machine Owners Responsibilities Safety Instructions Page Assembly Section Shipping Stand Removal Breather Plug InstallationTongue Assembly Installation Assembly Asm-FL-0066 Point Hitch Assembly Installation Attaching Optional Hydraulic Cylinder Attaching Axle Assemblies to Main Wheel BAR TubeOperation Section Operation CAT II-III Q.H OperationPersonal Protective Equipment PPE Operator RequirementsRops and Seat Belt Tractor Safety DevicesTractor Requirements and Capabilities Drawbar-Pull Type Mower Front End WeightPower Take Off PTO 3-Point HitchBoarding the Tractor Getting on and OFF the TractorDismounting the Tractor Starting the Tractor Connecting the Mower to the TractorSemi-Mount Models Setting the MowerPull Type Models Lift Type ModelsOperation Leveling Deck Driveline AttachmentDriveline Clearance Shorten the driveline profiles as follows PRE-OPERATION Inspection and ServiceEngagement Check Procedure Mower Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceSGM-10 Operation Driving the Tractor and Implement Starting the Tractor Raising the Mower Brake and Differential Lock SettingDriving the Tractor and Mower Turning ProcedureCrossing Ditches and Steep Inclines Operating the Tractor and Implement Operation Foreign Debris Hazards Bystanders/Passersby PrecautionsEngaging the Power Take Off PTO Operating the Mower PTO RPM and Ground SpeedOperation Shutting Down the Implement OPS-F-0012A Disconnecting the Mower from the TractorTransporting the Tractor and Implement Mower StorageOperation Transporting on Public Roadways OPS-U Hauling the Tractor and Implement Problem Possible Cause Remedy Trouble Shooting GuidePTO RPM Page Maintenance Section Lubrication General MaintenanceRoutine Maintenance Cutter Shaft Blade ReplacementBelt Adjustment and Replacement Pulley Alignment and Removal Maintenance Outer Cutter Shaft Bearing Removal InstallationCutter Shaft and Bearing Removal Cutter Shaft Bearing Removal Mnt-FL-0041Cutter Shaft Removal TOP Drive Assembly ServicingMnt-FL-0032 Driveline Shield ReplacementDriveline Figure Mnt-FL-0036 Pre-season Check Storing the RC12Rhino Required of the Operator Required of the OwnerRC12 12/05 00726339C Printed U.S.A