Servis-Rhino RC-12 manual Maintenance

Page 86

MAINTENANCE

MAINTENANCE

Never hammer edge of pulley which may crack. To move assembly, a soft blow hammer may be used on bushing only.

If the pulley is free and the bushing is still tight on shaft, it may be necessary to wedge a screwdriver in saw slot of bushing to loosen and move hub.

Do not apply excessive force which may split bushing.

Never apply lubrication to threads or mating surfaces when assembling pulley and bushing.

After correctly locating hub and placing key in shaft keyway, move pulley into position over taper hub and align tapped holes with through holes in hub. Install all mounting cap screws . Carefully tighten the cap screws alternately and progressively until tapers are seated. Check alignment of pulley and proceed to carefully tighten to 40 ft lbs torque. Maximum torque should be reached on each individual bolt only twice in the consecutive tightening.

RC12 12/05

Maintenance Section 5-6

© 2004 Alamo Group Inc.

Image 86

Contents RC-12 Warranty Information To the Owner/Operator/DealerTable of Contents Maintenance Section Safety Section Safety Wait a minute...Save a life Safety Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards Unless Safety Safety RC12 Safety Section STI-3 Safety MPH. STI-6 Maintenance and Service Safety Instructions and Practices Parts Information Concluding Safety Instructions and Practices Instruct PeligroReflect Name NFS SER PLTLogo ModelDecal Description Has stopped. P/N RC12 Safety Section Safety Safety Safety Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction Before Operating this Machine Owners Responsibilities Safety Instructions Page Assembly Section Shipping Stand Removal Breather Plug InstallationTongue Assembly Installation Assembly Asm-FL-0066 Point Hitch Assembly Installation Attaching Axle Assemblies to Main Wheel BAR Tube Attaching Optional Hydraulic CylinderOperation Section Operation Operation CAT II-III Q.HOperator Requirements Personal Protective Equipment PPERops and Seat Belt Tractor Safety DevicesTractor Requirements and Capabilities 3-Point Hitch Front End WeightPower Take Off PTO Drawbar-Pull Type MowerGetting on and OFF the Tractor Boarding the TractorDismounting the Tractor Connecting the Mower to the Tractor Starting the TractorLift Type Models Setting the MowerPull Type Models Semi-Mount ModelsOperation Driveline Attachment Leveling DeckDriveline Clearance Shorten the driveline profiles as follows PRE-OPERATION Inspection and ServiceEngagement Check Procedure Tractor Pre-Operation Inspection/Service Mower Pre-Operation Inspection/ServiceSGM-10 Operation Driving the Tractor and Implement Starting the Tractor Brake and Differential Lock Setting Raising the MowerTurning Procedure Driving the Tractor and MowerCrossing Ditches and Steep Inclines Operating the Tractor and Implement Operation Bystanders/Passersby Precautions Foreign Debris HazardsEngaging the Power Take Off PTO PTO RPM and Ground Speed Operating the MowerOperation Shutting Down the Implement Disconnecting the Mower from the Tractor OPS-F-0012AMower Storage Transporting the Tractor and ImplementOperation Transporting on Public Roadways OPS-U Hauling the Tractor and Implement Trouble Shooting Guide Problem Possible Cause RemedyPTO RPM Page Maintenance Section General Maintenance LubricationRoutine Maintenance Cutter Shaft Blade ReplacementBelt Adjustment and Replacement Pulley Alignment and Removal Maintenance Cutter Shaft Bearing Removal Mnt-FL-0041 InstallationCutter Shaft and Bearing Removal Outer Cutter Shaft Bearing RemovalTOP Drive Assembly Servicing Cutter Shaft RemovalMnt-FL-0032 Driveline Shield ReplacementDriveline Figure Mnt-FL-0036 Storing the RC12 Pre-season CheckRhino Required of the Owner Required of the OperatorRC12 12/05 00726339C Printed U.S.A