Servis-Rhino RC-12 manual Driveline Shield Replacement, Mnt-FL-0032

Page 89

MAINTENANCE

DRIVELINE:

Driveline Shield Replacement:

Slide apart both halves of driveline and remove shield by unfastening nylon bearing retainer. The Snap ring can be removed by inserting screwdriver under on end. Snap ring may also be accessed through slots in side of shield by bell-end. Always replace nylon bearing kit when installing a new shield. When assembling both portions of driveline, align phase key on end of square shaft half with groove in tube side.

Step 1: To disassemble the universal joint, remove the four snap rings. FIGURE

Mnt-FL-0032.

Step 2: With snap rings removed, support drive in vise, hold yoke in hand and tap on yoke to drive cup up out of yoke. FIGURE Mnt-FL-0033.

Step 3: Clamp vise as shown and tap on yoke to completely remove cup from yoke. Repeat step two and three for opposite cup FIGURE Mnt-FL-0034.

Step 4: Place universal cross in vise as shown and tap on yoke to remove cup.

Repeat step 3 for final removal. Drive remaining cup out with drift and hammer.

FIGURE Mnt-FL-0035.

RC12 12/05

Maintenance Section 5-9

© 2004 Alamo Group Inc.

MAINTENANCE

Image 89

Contents RC-12 To the Owner/Operator/Dealer Warranty InformationTable of Contents Maintenance Section Safety Section Safety Wait a minute...Save a life Safety Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards Unless Safety Safety RC12 Safety Section STI-3 Safety MPH. STI-6 Maintenance and Service Safety Instructions and Practices Parts Information Concluding Safety Instructions and Practices Instruct PeligroReflect Logo NFS SER PLTName ModelDecal Description Has stopped. P/N RC12 Safety Section Safety Safety Safety Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction Before Operating this Machine Owners Responsibilities Safety Instructions Page Assembly Section Shipping Stand Removal Breather Plug InstallationTongue Assembly Installation Assembly Asm-FL-0066 Point Hitch Assembly Installation Attaching Optional Hydraulic Cylinder Attaching Axle Assemblies to Main Wheel BAR TubeOperation Section Operation CAT II-III Q.H OperationPersonal Protective Equipment PPE Operator RequirementsRops and Seat Belt Tractor Safety DevicesTractor Requirements and Capabilities Power Take Off PTO Front End Weight3-Point Hitch Drawbar-Pull Type MowerBoarding the Tractor Getting on and OFF the TractorDismounting the Tractor Starting the Tractor Connecting the Mower to the TractorPull Type Models Setting the MowerLift Type Models Semi-Mount ModelsOperation Leveling Deck Driveline AttachmentDriveline Clearance Shorten the driveline profiles as follows PRE-OPERATION Inspection and ServiceEngagement Check Procedure Mower Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceSGM-10 Operation Driving the Tractor and Implement Starting the Tractor Raising the Mower Brake and Differential Lock SettingDriving the Tractor and Mower Turning ProcedureCrossing Ditches and Steep Inclines Operating the Tractor and Implement Operation Foreign Debris Hazards Bystanders/Passersby PrecautionsEngaging the Power Take Off PTO Operating the Mower PTO RPM and Ground SpeedOperation Shutting Down the Implement OPS-F-0012A Disconnecting the Mower from the TractorTransporting the Tractor and Implement Mower StorageOperation Transporting on Public Roadways OPS-U Hauling the Tractor and Implement Problem Possible Cause Remedy Trouble Shooting GuidePTO RPM Page Maintenance Section Lubrication General MaintenanceRoutine Maintenance Cutter Shaft Blade ReplacementBelt Adjustment and Replacement Pulley Alignment and Removal Maintenance Cutter Shaft and Bearing Removal InstallationCutter Shaft Bearing Removal Mnt-FL-0041 Outer Cutter Shaft Bearing RemovalCutter Shaft Removal TOP Drive Assembly ServicingMnt-FL-0032 Driveline Shield ReplacementDriveline Figure Mnt-FL-0036 Pre-season Check Storing the RC12Rhino Required of the Operator Required of the OwnerRC12 12/05 00726339C Printed U.S.A