Servis-Rhino RC-12 manual Operation, Cat Ii-Iii Q.H

Page 45

OPERATION

1. Standard Equipment and Specifications

RC 12

Cutting Width

144”

Overall Width

156”

Cutting Height Range

1-18”

Cuttershaft Diameter

10-3/4”

Lift Type Hitch

CAT II-III Q.H.

Semi Mount Hitch

CAT II-III Q.H.

Pull Type Hitch

Clevis

Min. HP Required (Lift type*)

90 HP

Min. HP Required (Semi-Mount)

90 HP

Min. HP Required (Pull type)

90 HP

Gearbox Rating**

207 HP

Blade Tip Speed

12,620 FPM

Rotor Speed

2000 RPM

Number of Knives

128

Driveline Size

CAT 5 or 6

Hood Thickness

3/16”

End Plate Thickness

1/4 “

Drive Belt

5 x 5V, Banded

Front Safety Deflectors

Std.

Weight (Approx.)

4025 lbs.

*with adequate front weights

 

**1000 RPM

 

The Mower is designed for certain mowing applications and is rated to cut up to a specific size vegetation (see Mower Standard Equipment and Specifications). DO NOT use this mower to cut vegetation above the Mower’s rated capacity or to cut any type of non-

vegetative material. Only operate this Mower on a properly sized and equipped Tractor. Operating this Mower in an application for which it is not designed and/or operating the Mower with the wrong size Tractor can cause Mower component damage and equipment failure resulting in possible serious injury or death. (SGM-14)

RC12 12/05

Operation Section 4-3

© 2005 Alamo Group Inc.

OPERATION

Image 45
Contents RC-12 To the Owner/Operator/Dealer Warranty InformationTable of Contents Maintenance Section Safety Section Safety Wait a minute...Save a life Safety Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards Unless Safety Safety RC12 Safety Section STI-3 Safety MPH. STI-6 Maintenance and Service Safety Instructions and Practices Parts Information Concluding Safety Instructions and Practices Peligro ReflectInstruct Logo NFS SER PLTName ModelDecal Description Has stopped. P/N RC12 Safety Section Safety Safety Safety Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction Before Operating this Machine Owners Responsibilities Safety Instructions Page Assembly Section Breather Plug Installation Tongue Assembly InstallationShipping Stand Removal Assembly Asm-FL-0066 Point Hitch Assembly Installation Attaching Optional Hydraulic Cylinder Attaching Axle Assemblies to Main Wheel BAR TubeOperation Section Operation CAT II-III Q.H OperationPersonal Protective Equipment PPE Operator RequirementsTractor Safety Devices Tractor Requirements and CapabilitiesRops and Seat Belt Power Take Off PTO Front End Weight3-Point Hitch Drawbar-Pull Type MowerBoarding the Tractor Getting on and OFF the TractorDismounting the Tractor Starting the Tractor Connecting the Mower to the TractorPull Type Models Setting the MowerLift Type Models Semi-Mount ModelsOperation Leveling Deck Driveline AttachmentDriveline Clearance PRE-OPERATION Inspection and Service Engagement Check ProcedureShorten the driveline profiles as follows Mower Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceSGM-10 Operation Driving the Tractor and Implement Starting the Tractor Raising the Mower Brake and Differential Lock SettingDriving the Tractor and Mower Turning ProcedureCrossing Ditches and Steep Inclines Operating the Tractor and Implement Operation Foreign Debris Hazards Bystanders/Passersby PrecautionsEngaging the Power Take Off PTO Operating the Mower PTO RPM and Ground SpeedOperation Shutting Down the Implement OPS-F-0012A Disconnecting the Mower from the TractorTransporting the Tractor and Implement Mower StorageOperation Transporting on Public Roadways OPS-U Hauling the Tractor and Implement Problem Possible Cause Remedy Trouble Shooting GuidePTO RPM Page Maintenance Section Lubrication General MaintenanceRoutine Maintenance Blade Replacement Belt Adjustment and ReplacementCutter Shaft Pulley Alignment and Removal Maintenance Cutter Shaft and Bearing Removal InstallationCutter Shaft Bearing Removal Mnt-FL-0041 Outer Cutter Shaft Bearing RemovalCutter Shaft Removal TOP Drive Assembly ServicingDriveline Shield Replacement DrivelineMnt-FL-0032 Figure Mnt-FL-0036 Pre-season Check Storing the RC12Rhino Required of the Operator Required of the OwnerRC12 12/05 00726339C Printed U.S.A