Servis-Rhino RC-12 manual Pulley Alignment and Removal

Page 85

MAINTENANCE

PULLEY ALIGNMENT AND REMOVAL

Pulleys will remain aligned during belt tension if inside pivot mount bolts (item 3) have not been loosened. Check alignment of pulleys by placing a straight edge along flat face of both pulleys. Check alignment at lower and upper end of pulley face when belt is tensioned.

If pulleys are not correctly aligned check tightness of pivot bolts (3). Drive tube inner mount (4) is slotted and may be moved toward front, rear or shimmed for height adjustment to correct pulley alignment. Mnt-FL-0039.

To relocate pulleys on drive and cuttershaft, first loosen belt tension and check for shaft movement to ensure they are not loose or have moved. Mark present location of bushing on shaft for future reference. Pulleys are locked to shaft by a tapered hub bushing. Loosen socket head set screw located above key. Loosen and remove all mounting cap screws in bushing. Insert cap screws in all threaded jack screw holes on bushing. Start with the screw furthest from the bushing slot and tighten all screws alternately and progressively. Keep turning the screws in small equal amounts until the bushing and pulley start disengaging. Mnt-FL-0040.

Uneven pressure on the jack screws may break the bushing flange.

Once both pulley and hub start seperating, attempt to move assembly on shaft.

RC12 12/05

Maintenance Section 5-5

© 2004 Alamo Group Inc.

MAINTENANCE

Image 85
Contents RC-12 To the Owner/Operator/Dealer Warranty InformationTable of Contents Maintenance Section Safety Section Safety Wait a minute...Save a life Safety Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards Unless Safety Safety RC12 Safety Section STI-3 Safety MPH. STI-6 Maintenance and Service Safety Instructions and Practices Parts Information Concluding Safety Instructions and Practices Reflect PeligroInstruct Logo NFS SER PLTName ModelDecal Description Has stopped. P/N RC12 Safety Section Safety Safety Safety Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction Before Operating this Machine Owners Responsibilities Safety Instructions Page Assembly Section Tongue Assembly Installation Breather Plug InstallationShipping Stand Removal Assembly Asm-FL-0066 Point Hitch Assembly Installation Attaching Optional Hydraulic Cylinder Attaching Axle Assemblies to Main Wheel BAR TubeOperation Section Operation CAT II-III Q.H OperationPersonal Protective Equipment PPE Operator RequirementsTractor Requirements and Capabilities Tractor Safety DevicesRops and Seat Belt Power Take Off PTO Front End Weight3-Point Hitch Drawbar-Pull Type MowerBoarding the Tractor Getting on and OFF the TractorDismounting the Tractor Starting the Tractor Connecting the Mower to the TractorPull Type Models Setting the MowerLift Type Models Semi-Mount ModelsOperation Leveling Deck Driveline AttachmentDriveline Clearance Engagement Check Procedure PRE-OPERATION Inspection and ServiceShorten the driveline profiles as follows Mower Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceSGM-10 Operation Driving the Tractor and Implement Starting the Tractor Raising the Mower Brake and Differential Lock SettingDriving the Tractor and Mower Turning ProcedureCrossing Ditches and Steep Inclines Operating the Tractor and Implement Operation Foreign Debris Hazards Bystanders/Passersby PrecautionsEngaging the Power Take Off PTO Operating the Mower PTO RPM and Ground SpeedOperation Shutting Down the Implement OPS-F-0012A Disconnecting the Mower from the TractorTransporting the Tractor and Implement Mower StorageOperation Transporting on Public Roadways OPS-U Hauling the Tractor and Implement Problem Possible Cause Remedy Trouble Shooting GuidePTO RPM Page Maintenance Section Lubrication General MaintenanceRoutine Maintenance Belt Adjustment and Replacement Blade ReplacementCutter Shaft Pulley Alignment and Removal Maintenance Cutter Shaft and Bearing Removal InstallationCutter Shaft Bearing Removal Mnt-FL-0041 Outer Cutter Shaft Bearing RemovalCutter Shaft Removal TOP Drive Assembly ServicingDriveline Driveline Shield ReplacementMnt-FL-0032 Figure Mnt-FL-0036 Pre-season Check Storing the RC12Rhino Required of the Operator Required of the OwnerRC12 12/05 00726339C Printed U.S.A