Lenovo 6444, 6447, 6446, 6445 manual Handling static-sensitive devices, Removing the cover

Page 23
Handling static-sensitive devices

The server supports hot-plug, hot-add, and hot-swap devices and is designed to operate safely while it is turned on and the cover is removed. Follow these guidelines when you work inside a server that is turned on:

vAvoid wearing loose-fitting clothing on your forearms. Button long-sleeved shirts before working inside the server; do not wear cuff links while you are working inside the server.

vDo not allow your necktie or scarf to hang inside the server.

vRemove jewelry, such as bracelets, necklaces, rings, and loose-fitting wrist watches.

vRemove items from your shirt pocket, such as pens and pencils, that could fall into the server as you lean over it.

vAvoid dropping any metallic objects, such as paper clips, hairpins, and screws, into the server.

Handling static-sensitive devices

Attention: Static electricity can damage the server and other electronic devices. To avoid damage, keep static-sensitive devices in their static-protective packages until you are ready to install them.

To reduce the possibility of damage from electrostatic discharge, observe the following precautions:

vLimit your movement. Movement can cause static electricity to build up around you.

vThe use of a grounding system is recommended. For example, wear an electrostatic-discharge wrist strap, if one is available. Always use an electrostatic-discharge wrist strap or other grounding system when working inside the server with the power on

vHandle the device carefully, holding it by its edges or its frame.

vDo not touch solder joints, pins, or exposed circuitry.

vDo not leave the device where others can handle and damage it.

vWhile the device is still in its static-protective package, touch it to an unpainted metal surface on the outside of the server for at least 2 seconds. This drains static electricity from the package and from your body.

vRemove the device from its package and install it directly into the server without setting down the device. If it is necessary to set down the device, put it back into its static-protective package. Do not place the device on the server cover or on a metal surface.

vTake additional care when handling devices during cold weather. Heating reduces indoor humidity and increases static electricity.

Removing the cover

Important: Before you install optional hardware, make sure that the server is working correctly. Start the server, and make sure that the operating system starts, if an operating system is installed, or that a 19990305 error code is displayed, indicating that an operating system was not found but the server is otherwise working correctly. If the server is not working correctly, see the Hardware Maintenance Manual for diagnostic information.

To remove the cover, complete the following steps:

1.Read the safety information that begins on page v and “Installationguidelines” on page 7.

Chapter 2. Installing optional devices 9

Image 23
Contents ThinkServer RD120 Types 6444, 6445, 6446, and Installation GuidePage ThinkServer RD120 Types 6444, 6445, 6446, and First Edition October Copyright Lenovo Chapter 4. Configuring the server ContentsChapter 3. Server controls, LEDs, and power Appendix A. Getting help and technical assistance Safety Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English-language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document Statement DANGER Statement Appareil A Laser de Classe Class 1 Laser Product Laser Klasse Laser Klass Luokan 1 Laserlaite `≥ 55 kg 121.2 lb ≥ 18 kg 39.7 lb≥ 32 kg 70.5 lb Statement This server is suitable for use on an IT power-distribution system whose maximum phase-to-phase voltage is 240 V under any distribution fault condition Chapter 1. Introduction The Lenovo ThinkServer Documentation DVD Hardware and software requirementsNotices and statements in this document Features and specificationsMicroprocessor Table 1. Features and specificationsMajor components of the server Power backplane Installation guidelines Chapter 2. Installing optional devicesSystem reliability guidelines Working inside the server with the power onRemoving the cover Handling static-sensitive devicesInstalling a memory module 1 1 and 2 7 and 3 2 and 4 8 and 5 3 and 6 9 and DIMM connectorsPair Page Memory mirroring 1 1, 4, 7, and 2 2, 5, 8, and 3 3, 6, 9, and Online-spare memoryTable 5. Online-spare DIMM configurations, basic scheme In the configuration that you use, install the largest DIMMs first3.5-inch drives Installing a hard disk drive2.5-inch drives Installing a tape driveInstalling an additional microprocessor Voltage regulator module connectorMicroprocessor socket dust cover 4. Remove the microprocessor air baffle Note The microprocessor fits only one way on the socket 8. Install a heat sink on the microprocessor Low-profile PCI Express adapter Installing an adapterPCI riser card Release tabs Access holesBattery Installing a Remote Supervisor Adapter II SlimLineHard disk drive cable connector 4 Hard disk drive cable connector 03. Remove the cover 4. Remove the PCI riser-card assembly Replacing the ServeRAID SAS controller Completing the installation Front view Installing the coverConnecting the cables Rear view Updating the server configurationIf you have installed or removed a hard disk drive, see “Usingthe RAID configuration programs” on page 44 for information about reconfiguring the disk arrays Page Front view Chapter 3. Server controls, LEDs, and powerHard disk drive activity LED Power-on LEDSystem-error LED Power-control buttonChapter 3. Server controls, LEDs, and power Rear viewServer power features Turning off the server Turning on the serverPage User Guide on the ThinkServer Documentation DVD Chapter 4. Configuring the serverUsing the ThinkServer EasyStartup program Page Configuring the Gigabit Ethernet controllers Using ThinkServer EasyManage productsUsing the Configuration/Setup Utility program Using the IBM ServeRAID Configuration Utility program Using the RAID configuration programsConfiguring the RAID controller Using ServeRAID ManagerStarting the IBM ServeRAID Configuration Utility program IBM ServeRAID Configuration Utility menu choices2. Click Custom configuration Viewing the configuration2. Click Express configuration BIOS update and configuration Using the baseboard management controllerRed Hat Enterprise Linux ES 4 configuration Linux configurationLILO configuration If you are using LILO, complete the following steps Original /etc/lilo.conf contents 2. Run the lilo command to store and activate the LILO configuration Original /boot/grub/grub.conf contents Modified /boot/grub/grub.conf contents SUSE SLES 9.0 configurationc. Append the following text to the first title line Original /boot/grub/menu.lst contentsModified /boot/grub/menu.lst contents b. Add the following line before the first title lineCOM1 and that redirectbaudrate is set to Microsoft Windows 2003 Standard Edition configurationInstalling the OSA SMBridge management utility program 3. Type mount/mnt/cdrom 3. Follow the prompts to complete the installationUsing the baseboard management controller utility programs Page Page v Diagnostics DVD Chapter 5. Solving problemsDiagnostic tools overview POST beep codesOther beep codes Failing device or POST error codesproblem found POSTAction EasyStartup problemsSymptom Table 8. ThinkServer EasyStartup DVDCD-RW/DVD drive problems Troubleshooting tablesHard disk drive problems General problemsthe Hardware Maintenance Manual Intermittent problemsUSB keyboard, mouse, or pointing-device problems Hardware Maintenance Manual Memory problemsLEDs” in the Hardware Maintenance Manual Microprocessor problemsMonitor problems Page Power problems Optional-device problemsHardware Maintenance Manual Serial port problems Software problems Light path diagnostics Universal Serial Bus USB port problemsVideo problems Light path diagnostics LEDs Diagnosing problems using light path diagnosticsthe User Guide on the ThinkServer Documentation DVD for Action Before you call Using the documentationAppendix A. Getting help and technical assistance Getting help and information from the World Wide Web Calling for serviceAppendix A. Getting help and technical assistance Using other servicesPurchasing additional services Lenovo product servicePage Morrisville, NC U.S.A Attention Lenovo Director of Licensing Appendix B. NoticesLenovo United States, Inc 1009 Think Place - Building One Important notes TrademarksAppendix B. Notices Waste electrical and electronic equipment WEEE noticesFor the European Union Battery return programFor California German Ordinance for Work gloss statementElectronic emissions notices Federal Communications Commission FCC statementAustralia and New Zealand Class A statement United Kingdom telecommunications safety requirementIndustry Canada Class A emission compliance statement Avis de conformité à la réglementation dIndustrie CanadaDas Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN Japanese Voluntary Control Council for Interference VCCI statementDeutschland BetriebsmitteinKorean Class A warning statement Taiwanese Class A warning statement Chinese Class A warning statementIndex A See SAS Index software problemsconnectors Page Page 1P P/N 46U0862 Part Number 46U0862 Printed in USA