Lenovo 6444, 6447, 6446, 6445 manual Installing a tape drive, inch drives

Page 31
2.5-inch drives

2.5-inch drives

To install a drive in a hot-swap bay, complete the following steps:

Attention: To maintain proper system cooling, do not operate the server for more than 10 minutes without either a drive or a filler panel installed in each bay.

1.Read the safety information that begins on page v, and “Installationguidelines” on page 7.

2.Remove the filler panel from one of the empty hot-swap bays.

3.Install the hard disk drive in the hot-swap bay:

a.Make sure that the tray handle is open (that is, perpendicular to the drive).

b.Align the drive assembly with the guide rails in the bay.

c.Gently push the drive assembly into the bay until the drive stops.

d.Push the tray handle to the closed (locked) position.

e.Check the hard disk drive status LED to verify that the hard disk drive is operating correctly.

If the amber hard disk drive status LED for a drive is lit continuously, that drive is faulty and must be replaced. If the green hard disk drive activity LED is flashing, the drive is being accessed.

Note: You might have to reconfigure the disk arrays after you install hard disk drives. See the RAID documentation on the ThinkServer Documentation DVD for information about RAID controllers.

If you have other optional devices to install or remove, do so now. Otherwise, go to “Completingthe installation” on page 30.

Installing a tape drive

For information about installing an optional tape drive, see the User Guide on the ThinkServer Documentation DVD, which comes with the server.

Chapter 2. Installing optional devices 17

Image 31
Contents ThinkServer RD120 Types 6444, 6445, 6446, and Installation GuidePage ThinkServer RD120 Types 6444, 6445, 6446, and First Edition October Copyright Lenovo Chapter 3. Server controls, LEDs, and power ContentsChapter 4. Configuring the server Appendix A. Getting help and technical assistance Safety Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English-language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document Statement DANGER Statement Appareil A Laser de Classe Class 1 Laser Product Laser Klasse Laser Klass Luokan 1 Laserlaite `≥ 32 kg 70.5 lb ≥ 18 kg 39.7 lb≥ 55 kg 121.2 lb Statement This server is suitable for use on an IT power-distribution system whose maximum phase-to-phase voltage is 240 V under any distribution fault condition Chapter 1. Introduction The Lenovo ThinkServer Documentation DVD Hardware and software requirementsNotices and statements in this document Features and specificationsMicroprocessor Table 1. Features and specificationsMajor components of the server Power backplane Installation guidelines Chapter 2. Installing optional devicesSystem reliability guidelines Working inside the server with the power onRemoving the cover Handling static-sensitive devicesInstalling a memory module Pair DIMM connectors1 1 and 2 7 and 3 2 and 4 8 and 5 3 and 6 9 and Page Memory mirroring 1 1, 4, 7, and 2 2, 5, 8, and 3 3, 6, 9, and Online-spare memoryTable 5. Online-spare DIMM configurations, basic scheme In the configuration that you use, install the largest DIMMs first3.5-inch drives Installing a hard disk drive2.5-inch drives Installing a tape driveInstalling an additional microprocessor Voltage regulator module connectorMicroprocessor socket dust cover 4. Remove the microprocessor air baffle Note The microprocessor fits only one way on the socket 8. Install a heat sink on the microprocessor Low-profile PCI Express adapter Installing an adapterPCI riser card Release tabs Access holesBattery Installing a Remote Supervisor Adapter II SlimLineHard disk drive cable connector 4 Hard disk drive cable connector 03. Remove the cover 4. Remove the PCI riser-card assembly Replacing the ServeRAID SAS controller Completing the installation Connecting the cables Installing the coverFront view Rear view Updating the server configurationIf you have installed or removed a hard disk drive, see “Usingthe RAID configuration programs” on page 44 for information about reconfiguring the disk arrays Page Front view Chapter 3. Server controls, LEDs, and powerHard disk drive activity LED Power-on LEDSystem-error LED Power-control buttonChapter 3. Server controls, LEDs, and power Rear viewServer power features Turning off the server Turning on the serverPage Using the ThinkServer EasyStartup program Chapter 4. Configuring the serverUser Guide on the ThinkServer Documentation DVD Page Using the Configuration/Setup Utility program Using ThinkServer EasyManage productsConfiguring the Gigabit Ethernet controllers Using the IBM ServeRAID Configuration Utility program Using the RAID configuration programsConfiguring the RAID controller Using ServeRAID ManagerStarting the IBM ServeRAID Configuration Utility program IBM ServeRAID Configuration Utility menu choices2. Click Express configuration Viewing the configuration2. Click Custom configuration BIOS update and configuration Using the baseboard management controllerRed Hat Enterprise Linux ES 4 configuration Linux configurationLILO configuration If you are using LILO, complete the following steps Original /etc/lilo.conf contents 2. Run the lilo command to store and activate the LILO configuration Original /boot/grub/grub.conf contents Modified /boot/grub/grub.conf contents SUSE SLES 9.0 configurationc. Append the following text to the first title line Original /boot/grub/menu.lst contentsModified /boot/grub/menu.lst contents b. Add the following line before the first title lineCOM1 and that redirectbaudrate is set to Microsoft Windows 2003 Standard Edition configurationInstalling the OSA SMBridge management utility program 3. Type mount/mnt/cdrom 3. Follow the prompts to complete the installationUsing the baseboard management controller utility programs Page Page v Diagnostics DVD Chapter 5. Solving problemsDiagnostic tools overview POST beep codesOther beep codes Failing device or POST error codesproblem found POSTAction EasyStartup problemsSymptom Table 8. ThinkServer EasyStartup DVDCD-RW/DVD drive problems Troubleshooting tablesHard disk drive problems General problemsthe Hardware Maintenance Manual Intermittent problemsUSB keyboard, mouse, or pointing-device problems Hardware Maintenance Manual Memory problemsLEDs” in the Hardware Maintenance Manual Microprocessor problemsMonitor problems Page Power problems Optional-device problemsHardware Maintenance Manual Serial port problems Software problems Video problems Universal Serial Bus USB port problemsLight path diagnostics Light path diagnostics LEDs Diagnosing problems using light path diagnosticsthe User Guide on the ThinkServer Documentation DVD for Action Appendix A. Getting help and technical assistance Using the documentationBefore you call Getting help and information from the World Wide Web Calling for serviceAppendix A. Getting help and technical assistance Using other servicesPurchasing additional services Lenovo product servicePage Lenovo United States, Inc 1009 Think Place - Building One Appendix B. NoticesMorrisville, NC U.S.A Attention Lenovo Director of Licensing Important notes TrademarksAppendix B. Notices Waste electrical and electronic equipment WEEE noticesFor the European Union Battery return programFor California German Ordinance for Work gloss statementElectronic emissions notices Federal Communications Commission FCC statementAustralia and New Zealand Class A statement United Kingdom telecommunications safety requirementIndustry Canada Class A emission compliance statement Avis de conformité à la réglementation dIndustrie CanadaDas Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN Japanese Voluntary Control Council for Interference VCCI statementDeutschland BetriebsmitteinKorean Class A warning statement Taiwanese Class A warning statement Chinese Class A warning statementIndex A See SAS connectors software problemsIndex Page Page 1P P/N 46U0862 Part Number 46U0862 Printed in USA