Sanyo PLC-XT20L*, PLC-XT25K Basic Operation, Turning On the Projector, PIN Code Input Dialog Box

Page 25

Basic Operation

Turning On the Projector

1

Complete peripheral connections (with a computer,

 

VCR, etc.) before turning on the projector.

2

Connect the projector’s AC power cord into an AC

 

outlet. The POWER indicator lights green.

3

Press the ON/STAND-BY button on the top control or

 

the ON button on the remote control. The LAMP

 

indicator lights red and the cooling fans start to operate.

 

The preparation display appears on the screen and the

 

count down starts.

4

After the countdown, the input source that was

 

selected the last time and the lamp control status icon

(see page 54) appear on the screen.

If the projector is locked with a PIN code, PIN code input dialog box will appear. Enter the PIN code as instructed below.

Enter a PIN code

Use the Point ed buttons or Number buttons on the remote control to enter a number. Press the Point 8 button to fix the number and move the red frame pointer to the next box. The number changes to “.” If you fixed an incorrect number, use the Point 7 button to move the pointer to the number you want to correct, and then enter the correct number.

Repeat this step to complete entering a four-digit number.

After entering the four-digit number, move the pointer to “Set.” Press the SELECT button so that you can start to operate the projector.

If you entered an incorrect PIN code, “PIN code” and the number (✳✳✳✳) will turn red for a moment. Enter the correct PIN code all over again.

What is PIN code?

PIN (Personal Identification Number) code is a security code that allows the person who knows it to operate the projector. Setting a PIN code prevents unauthorized use of the projector.

A PIN code consists of a four-digit number. Refer to the PIN code lock function in the Setting Menu on pages 60–61 for locking operation of the projector with your PIN code.

CAUTION ON HANDLING PIN CODE

If you forget your PIN code, the projector can no longer be started. Take a special care in setting a new PIN code; write down the number in a column on page 81 of this manual and keep it at hand. Should the PIN code be missing or forgotten, consult your dealer or service center.

16

The preparation display will disappear after 30 seconds.

Selected Input Source and Lamp Control

Lamp control status See page 54 for the Lamp control status.

Note:

•The Filter warning and Lamp replacement icons may appear on the screen depending on the usage state of the projector.

PIN Code Input Dialog Box

After the OK icon disappears, you can operate the projector.

Notes:

•When the Logo select function is set to “Off,” the logo will not be shown on the screen (p.55).

•When the “Countdown off” or “Off” is selected in the Display function, the countdown will not be shown on the screen (p.57).

•During the countdown period, all operations are invalid.

•If the correct PIN code number is not entered within three minutes after the PIN code dialog box appeared, the projector will be turned off automatically.

•The “1234” is set as the initial PIN code at the factory.

25

Image 25
Contents Multimedia Projector Compact Design Power Management Features and DesignTable of Contents Risk of Electric Shock Do not Open To the OwnerSafety Instructions Top Control Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsTransporting the Projector Moving the ProjectorAC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Front Back Bottom Part Names and FunctionsRear Terminal 4INFRARED Remote Receiver Back Reset buttonTop Control Remote Control 9RESET/ON/ALL-OFF switch 4P-TIMER button3MENU button 5D.ZOOM buttonPointer Function Laser Pointer FunctionSpotlight Pointer Remote Control Code Wireless Mouse OperationRemote Control Receivers and Operating Range Remote Control Battery InstallationAdjustable Feet Lens Installation InstallationRemoving the lens Attaching the lens to the projectorMoving the Lens Positioning the Projector for PLC-XT25/XT25K/XT21/XT20/XT20KProjector side AC outlet side Connecting the AC Power CordCables used for connection Connecting to a Computer Digital and Analog RGBConnecting to Video Equipment Video, S-Video Connecting to Video Equipment Component and RGB Scart Turning On the Projector Basic OperationSelected Input Source and Lamp Control PIN Code Input Dialog BoxTurning Off the Projector Remote Control How to Operate the On-Screen MenuOn-Screen Menu Menu Bar Lens Operation Operating with Projector ControlInformation Direct Operation Sound AdjustmentMenu Operation Operating with Remote Control No Show button Timer buttonKeystone button Input Selection Remote Control button operation Remote Control OperationInput Top Control OperationInput Menu Input Source SelectionRGB PC analog RGB Scart RGB PC digital Video ComponentVideo or S-Video Video System SelectionComponent AV System Menu Video or S-VideoHelpful Hints Computer AdjustmentSelecting Computer System Manually Computer System SelectionPC System Menu PC Adjust Menu Auto PC AdjustmentTo store adjustment parameters Auto PC AdjManual PC Adjustment To store the adjusted data To clear the adjusted dataMemo Image Mode Selection Image Menu Image Mode SelectionImage Adjustment Image Adjust Menu Image AdjustmentGamma SharpnessNoise reduction ProgressiveTo reset the adjusted data, select Reset and press Screen Adjustment Screen Menu Screen AdjustmentKeystone Screen Size Adjustment Computer Signals Screen Size Adjustment Video, Component Signals Setting Setting Menu Language SettingPointer Logo Capture Logo Logo and Logo PIN code lock settingsLogo select CaptureEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code Logo PIN code lockRemote control Display Power management Power managementOn start Key lock Fan controlEnter a PIN code Change the PIN code lock settingPIN code lock Test pattern Change the PIN codeLamp counter Factory default Factory defaultFilter counter Filter counterRecommendation Maintenance and Filter CleaningPage Replacement Lamp Type No. POA-LMP105 Service Parts No 330 Lamp ReplacementReset the lamp counter Model No. of your projectorLamp counter Resetting the Lamp CounterThen check the matters below Projector is shut down and all five indicators are blinkingCleaning the Projector Cabinet Cleaning the Projection LensAppendix TroubleshootingAppendix Input Menu TreeInformation Input Setting PC Adjust ScreenProjector Condition Indicators and Projector ConditionOr replace the filter see below Lamp Replace indicatorON-SCREEN Resolution Compatible Computer Specifications31.47 59.94 Technical Specifications Optional Parts AccessoriesPJ Link Notice USB Connector Series B Configurations of TerminalsTerminal Analog RGB Mini D-sub 15 pin Terminal Mini DIN 8-PINLogo PIN Code Lock No PIN Code Number MemoDimensions MZ7A-B