Kodak 1200I manual Raise Printer, Voltage Configuration for dryer system, Reservoir Installation

Page 11

KODAK 1200i WIDE-FORMAT PRINTING SYSTEM

Step 5: Raise Printer

- Using a four (4) person lift gently raise printer to the standing position.

Step 6: Voltage Configuration (for dryer system)

Prior to powering on printer ensure the voltage selector switch is set to either 115V or 230V depending on line source.

NOTE 1: The voltage selector ships in the 230V position.

NOTE 2: the circuit beaker will ‘pop’ out in an over- current condition and will need to be replaced if this occurs.

Step 7: Reservoir Installation

When installing the six (6) ink bottles ensure each bottle is installed straight up and down to avoid damaging pins at intermediate reservoir (located at base).

Firmware Note:

C1 = CL

M1 = ML

Note: wait 5 minutes prior to conducting line filling operation (using ‘Pump On’ from the control panel or ink line may not fill properly.

NOTE: during normal operation you will have only 30 seconds to change ink bottles during print operations or a printer STOP error will occur.

Technical Training Guide

11

Image 11
Contents Technical Training Guide Operational Space Requirements Presite Inspection pre-installationInstallation Requirements Connectivity Requirements Power RequirementsIntelligent Mask Technology IMT Printer FeaturesInk System Ink Reservoir Rapid Dryer TechnologyCartridge / Printhead Carriage AssemblyIntermediate Reservoir Ink Supply Dampers and Septum Valve SystemAuto Clean Unit Service StationPrint Speeds Power SupplyMedia Handling System Shipping Brackets Removal Printer Installation Quick StepsMedia System Installation 1 electrical connection Crossbar Installation Raise Printer Voltage Configuration for dryer systemReservoir Installation Ink Line Filling Cartridge InstallationActivate ‘Prime All’ Test Pattern Printer Calibrations Example Assignments Example Assignments Color Cal Vertical. Select Utility Menu Best Quality ModePrint Pass Modes 2, 3, 4, 6, 8, 10, 12 Networking Peer-to-peer Windows 2000/XP example Kodak 1200i WIDE-FORMAT Printing System Load Windows Driver Kodak 1200i WIDE-FORMAT Printing System RIP Configuration Double-check example onlyQi Dye Print Mode & Dryer GuidelinesQi Pigment Lamination Guidelines Kodak Media Lamination Reference for Kodak 1200i PrinterQi Pigment Media Load and Verification Printer Operation TipsDryer Modes ‘Perfect’ Media LoadHumidity Control Edge Band modeSoftware Control Tips Typical Server Installation one per subnetClient Installation one per workstation When a Print Head is Replaced Printer MaintenancePerform the following ServiceRoutine Maintenance Kodak 1200i WIDE-FORMAT Printing System Clean the following items as required Cleaning Procedure Cleaning Procedure Replace the following item as required Preventive Maintenance Technical Bulletin Bulletin Reference ListKodak Cartridge Error Messages/Cartridge Failures Error Message CodesType 3 Internal cartridge errors Kodak 1200i WIDE-FORMAT Printing System Kodak 1200i WIDE-FORMAT Printing System If you then press the F1 key on the display you should see Black XXXmLAPC UNAVAILABLE, Abort JOB? Color Pen Error Invalid Pen ID PEN Error JOB PausedColor Pen Error Ink Warranty Mismatch Color INK Bottle Error = Code Bottle Error JOB PausedColor Bottle Error Code # # ranges from 2 to Color Warning INK Reservoir LOW Kodak 1200i WIDE-FORMAT Printing System Dryer System Fault Dryer OFF Dryer Sensor FaultDryer Temp TOO High Dryer OFF Dryer WARMING-UP. Print ANYWAY?Internal Shutdown Carriage Axis Failure Miscellaneous Error MessagesKodak 1200i WIDE-FORMAT Printing System Empty Waste Bottle NOW JOB Pause OUT of PaperPaper not Loaded JOB Pause E.O.M. DetectedWaste Bottle Missing Mainboard ID ErrorMbid Error Invalid OEM ID Bottle Error Waiting for Cartridge AccessCarriage Fpga Error PEN ErrorKodak 1200i WIDE-FORMAT Printing System Bubbles Observed in Ink Delivery Lines MAX INK TEMP. Advanced AnalysisMax Ink Temp. Errors Kodak 1200i WIDE-FORMAT Printing System Utility Menu Prime Menu Service Station Menu System Prime Data Shift Printer Grounding/Static ControlKodak 1200i WIDE-FORMAT Printing System Intermittent Banding/Improper Print Proper Power Cord & GroundingAir Plenum Grounding HumidifiersAnt-Static Mats Rear Static Strip Condition & Grounding Testing AC level on printer chassisTesting Receptacle Neutral-to-Ground Voltage Verify Proper Receptacle ConfigurationPower/Voltage Testers Secondary Grounding Common Mistakes by Technicians/CustomersProng to 2-Prong Adapters AC Isolation Transformers Related Print Symptoms
Related manuals
Manual 7 pages 43.35 Kb