Kodak 1200I manual Dryer WARMING-UP. Print ANYWAY?, Dryer Temp TOO High Dryer OFF

Page 54

KODAK 1200i WIDE-FORMAT PRINTING SYSTEM

3.Check a voltage switch setting. CAUTION: Remove power from printer. Verify the proper alternating current voltage setting is fully engaged [either to the left (115 volts) or to the right (230 volts)] as per the regional power provided. Power off printer and cycle voltage switch to verify position.

NOTE: If switched to 230V when only using 115V, you will typically get the ‘DRYER SYSTEM FAULT - DRYER OFF’

error message, but sometimes not until after you begin the print. (It can heat a nose that is not losing energy to a print, but cannot maintain set-point once water starts evaporating out of the ink.) If the situation is reversed, switched to 115V when using 230V, many times the dryer will operate normally but may give intermittent ‘OverTemp’ errors or ‘pop’ the circuit breaker (adjacent to switch).

NOTE: Since the dryer is turned off automatically the error condition may disappear as soon as the alarm is displayed.

Action: Contact technical support.

DRYER WARMING-UP. PRINT ANYWAY?

1.Error condition occurs (and sounds a beep) when a print job is processed and the current nose/dryer temperature is below a certain value of target temperature.

2.Error condition will inhibit all printing. Select “Ok” to start print processing; error message warning will be ignored. Select “Cancel” to pause print processing; when the nose heaters come up to temperature printing will start automatically (typically takes 2-8 minutes depending on the heat setting entered).

Action: None – Operation is normal

DRYER TEMP TOO HIGH - DRYER OFF

1.Error condition activates if either sensor reads above 72 ºC (surface temperature is 70 ºC). Dryer will be turned off automatically.

2.Error will repeat (and sound a beep again) if the user attempts to turn on the dryer (until sensor temperature alarm level drops below 72 ºC)

Action: Contact technical support.

Technical Training Guide

54

Image 54
Contents Technical Training Guide Presite Inspection pre-installation Installation RequirementsOperational Space Requirements Power Requirements Connectivity RequirementsPrinter Features Intelligent Mask Technology IMTRapid Dryer Technology Ink System Ink ReservoirInk Supply Dampers and Septum Valve System Carriage AssemblyIntermediate Reservoir Cartridge / PrintheadService Station Auto Clean UnitPower Supply Media Handling SystemPrint Speeds Printer Installation Quick Steps Media System Installation 1 electrical connectionShipping Brackets Removal Crossbar Installation Voltage Configuration for dryer system Reservoir InstallationRaise Printer Cartridge Installation Ink Line FillingActivate ‘Prime All’ Test Pattern Printer Calibrations Example Assignments Example Assignments Best Quality Mode Print Pass Modes 2, 3, 4, 6, 8, 10, 12Color Cal Vertical. Select Utility Menu Networking Peer-to-peer Windows 2000/XP example Kodak 1200i WIDE-FORMAT Printing System Load Windows Driver Kodak 1200i WIDE-FORMAT Printing System Configuration Double-check example only RIPPrint Mode & Dryer Guidelines Qi DyeQi Pigment Kodak Media Lamination Reference for Kodak 1200i Printer Lamination GuidelinesQi Pigment Printer Operation Tips Media Load and Verification‘Perfect’ Media Load Dryer ModesEdge Band mode Humidity ControlTypical Server Installation one per subnet Client Installation one per workstationSoftware Control Tips Printer Maintenance When a Print Head is ReplacedService Perform the followingRoutine Maintenance Kodak 1200i WIDE-FORMAT Printing System Clean the following items as required Cleaning Procedure Cleaning Procedure Replace the following item as required Preventive Maintenance Bulletin Reference List KodakTechnical Bulletin Error Message Codes Cartridge Error Messages/Cartridge FailuresType 3 Internal cartridge errors Kodak 1200i WIDE-FORMAT Printing System Kodak 1200i WIDE-FORMAT Printing System Black XXXmL If you then press the F1 key on the display you should seeAPC UNAVAILABLE, Abort JOB? PEN Error JOB Paused Color Pen Error Invalid Pen IDColor Pen Error Ink Warranty Mismatch Bottle Error JOB Paused Color INK Bottle Error = CodeColor Bottle Error Code # # ranges from 2 to Color Warning INK Reservoir LOW Kodak 1200i WIDE-FORMAT Printing System Dryer Sensor Fault Dryer System Fault Dryer OFFDryer WARMING-UP. Print ANYWAY? Dryer Temp TOO High Dryer OFFMiscellaneous Error Messages Internal Shutdown Carriage Axis FailureKodak 1200i WIDE-FORMAT Printing System JOB Pause E.O.M. Detected JOB Pause OUT of PaperPaper not Loaded Empty Waste Bottle NOWMainboard ID Error Mbid Error Invalid OEM IDWaste Bottle Missing PEN Error Waiting for Cartridge AccessCarriage Fpga Error Bottle ErrorKodak 1200i WIDE-FORMAT Printing System MAX INK TEMP. Advanced Analysis Bubbles Observed in Ink Delivery LinesMax Ink Temp. Errors Kodak 1200i WIDE-FORMAT Printing System Utility Menu Prime Menu Service Station Menu System Prime Printer Grounding/Static Control Data ShiftKodak 1200i WIDE-FORMAT Printing System Proper Power Cord & Grounding Intermittent Banding/Improper PrintHumidifiers Ant-Static MatsAir Plenum Grounding Testing AC level on printer chassis Rear Static Strip Condition & GroundingVerify Proper Receptacle Configuration Testing Receptacle Neutral-to-Ground VoltagePower/Voltage Testers Common Mistakes by Technicians/Customers Secondary GroundingProng to 2-Prong Adapters Related Print Symptoms AC Isolation Transformers
Related manuals
Manual 7 pages 43.35 Kb