Philips RFX9400 manual Support, Troubleshooting, What Do the LEDs Indicate?

Page 10

RFX9400 Starter’s Guide

-or-

• a mini-jack IR cable.

Insert one mini-jack connector of the mini-jack cable in the IR output of the Extender.

Insert the other mini-jack connector in the AV-component.

Adjusting the Power Level of the IR Outputs

At the back of the Extender, there are 4 dipswitches, one for each IR output. Use these dipswitches to configure the power level of the Dual IR emitters and the mini-jack cables.

For example, flip the dipswitch down to lower the power level when the Extender is connected to an external IR bus system.

Support

Troubleshooting

What Do the LEDs Indicate?

	LEDs	Ethernet LED	WiFi LED	Busy LED
	Colors	Ethernet LED	WiFi LED	Busy LED
	Colors
	Green blinking	The Extender’s IP address is	The Extender’s IP address is	The Extender is busy processing
		being determined.	being determined.	a short code or macro from the
				Control Panel.
	Green	The Extender is functioning	The Extender is functioning	The Extender is busy processing
		normally.	normally.	a long macro from the Control
				Panel.
	Red/green blinking	–	–	The Extender is being
				configured.
	Red	Refer to the topic ‘There is an	Refer to the topic	Refer to the topic ‘There are
		IP conflict’ on page 7.	‘The Extender cannot	duplicate Extender IDs’
			communicate with the	on page 8.
	Red blinking	Refer to the topic ‘The IP address	wireless network’ on page 8.	The Extender is starting up.
		cannot be determined’ on		Wait until startup has finished.
		page 7.

There is an IP conflict

There is another AV-component in the network that is using the same fixed IP address as the Extender. Change the IP address of the Extender in the Configuration Tool.

If the problem persists, check the router settings.

The IP address cannot be determined

•When using the Extender: make sure that the Extender is connected to the router with a straight Ethernet cable.

7

Image 10

Contents Manual de inicio Page Starter’s Guide Contents Before You Start Stand-alone ModeNetwork Mode Stand-alone AdvantagesPronto Wireless Extender Unpacking the ExtenderWireless connection Configuring the ExtenderUse the default switch settings of the Extender Stand-alone ConnectionConfiguration cable this is the crossed Extender will restart. After startupConnecting the Extender to AV-equipment Installing the ExtenderConfiguring the Extender through a Router Set the Extender’s Configuration switch toSupport TroubleshootingWhat Do the LEDs Indicate? Finding the Exact Location of an AV-component’s IR Receiver Extender cannot communicate with the wireless networkAV-components do not respond to commands from the Extender Operating AV-components with the ExtenderBusy LED blinks green when the Control Panel is not in use Firmware UpdateResetting the Extender Updating the Extender with the configuration cablePronto Wireless Extender Starter’s Guide SpecificationsRemarks Contenido Contenido del paquete del ExtensorModo Network modo red Antes de empezarModo Stand-alone modo autónomo Ventajas del modo Stand-aloneContenido del paquete del Extensor Conexión Network Configuración del ExtensorConexión Stand-alone Conexión inalámbricaMacro desde el Control Panel Conexión del Extensor a un equipo AV Configuración del Extensor a través de un routerInstalación del Extensor Abra ProntoEdit Professional en el PCAsistencia Detección de errores¿Qué indican los indicadores LED? Funcionamiento de los componentes AV con el Extensor El indicador LED WiFi está iluminado en rojoEl indicador LED WiFi parpadea en rojo Hay ID del Extensor duplicadosReinicialización del Extensor Actualización del Extensor con el cable de configuraciónActualización de Firmware Actualización del Extensor a través de un routerEspecificaciones Pronto Wireless Extender Manual de inicioObservaciones RFX9400FX9400 Guide deGuidedémarragede démarrage Table des matièresAvantages du mode Stand-alone autonome Mode Stand-alone autonomeMode Network réseau Avantages du mode Network réseauDéballage du Prolongateur Connexion Network réseau Configuration du ProlongateurConnexion Stand-alone autonome Connexion filaireBranchez l’adaptateur secteur du Prolongateur Control PanelPlacez le commutateur de configuration du Prolongateur sur Installation du ProlongateurConfiguration du Prolongateur par un routeur Connexion du Prolongateur à l’équipement audio/vidéoAjustement du niveau de puissance des sorties IR DépannageQu’indiquent les voyants ? Il existe un conflit IPLe voyant WiFi est rouge et clignote Le voyant WiFi est rougeIl existe des ID de Prolongateur dupliqués Mise à jour du micrologiciel Configuration du Prolongateur par un routeurRéinitialisation du Prolongateur Spécifications Guide de démarrage du Pronto Wireless ExtenderRemarques IFU Approbation / Safety Content RFX9400 FCC CompliancyRegulations According to R&TTE DeclarationDeclaration of Conformity of this product can be found at Declaration of ConformityDoCMarking IiiItalian Smaltimento di vecchi prodotti French Mise au rebut des produits en fin de vieGerman Entsorgung Ihres alten Geräts Norwegian Avhending av gamle produkterSlovak Likvidácia tohto produktu Polish Usuwanie zużytych produktówEliminação do seu antigo produto Slovenian Odlaganje starega izdelka3104 205