Philips RFX9400 Firmware Update, Resetting the Extender, Updating the Extender through a router

Page 12

RFX9400 Starter’s Guide

The Busy LED blinks green when the Control Panel is not in use

This does not mean that something is wrong with the Extender. It merely indicates that the Extender is being operated by a different Control Panel. When the Busy LED stops blinking, you can use the Extender again.

Resetting the Extender

This is only necessary when the Extender displays unusual behavior.

To perform a reset, unplug the Extender from the electrical socket. Wait a few seconds, and plug it in again.

Firmware Update

When an update of the Extender firmware is available, this will be announced on the Philips Pronto website: www.pronto.philips.com.

Note You can always see the current version of the firmware in the Configuration Tool.

1Download the new version of the firmware on the PC.

2Unplug the Extender. The Extender can be updated in the following ways.

Updating the Extender with the configuration cable

1Connect the Extender to the PC with the configuration cable.

2Set the switches correctly.

Stand-alone/Network	Network
Configuration switch	2
Extender ID	0

3Open the browser.

4Type the IP address of the Extender (printed on the bottom of the Extender) in the address bar of the browser.

The Configuration Tool opens in the browser.

5Select Firmware Update in the left navigation pane. The Firmware Update page opens.

6Follow the onscreen instructions.

Updating the Extender through a router

If the Extender is already installed and connected to AV-equipment, it may be more convenient to update it through a router.

1Connect the Extender to the router, and the router to the PC.

2Set the switches correctly.

Stand-alone/Network	Network
Configuration switch	3
Extender ID	0

9

Image 12

Contents Manual de inicio Page Starter’s Guide Contents Stand-alone Mode Network ModeBefore You Start Stand-alone AdvantagesPronto Wireless Extender Unpacking the ExtenderConfiguring the Extender Use the default switch settings of the ExtenderWireless connection Stand-alone ConnectionConfiguration cable this is the crossed Extender will restart. After startupInstalling the Extender Configuring the Extender through a RouterConnecting the Extender to AV-equipment Set the Extender’s Configuration switch toTroubleshooting SupportWhat Do the LEDs Indicate? Extender cannot communicate with the wireless network AV-components do not respond to commands from the ExtenderFinding the Exact Location of an AV-component’s IR Receiver Operating AV-components with the ExtenderFirmware Update Resetting the ExtenderBusy LED blinks green when the Control Panel is not in use Updating the Extender with the configuration cableSpecifications Pronto Wireless Extender Starter’s GuideRemarks Contenido Contenido del paquete del ExtensorAntes de empezar Modo Stand-alone modo autónomoModo Network modo red Ventajas del modo Stand-aloneContenido del paquete del Extensor Configuración del Extensor Conexión Stand-aloneConexión Network Conexión inalámbricaMacro desde el Control Panel Configuración del Extensor a través de un router Instalación del ExtensorConexión del Extensor a un equipo AV Abra ProntoEdit Professional en el PCDetección de errores Asistencia¿Qué indican los indicadores LED? El indicador LED WiFi está iluminado en rojo El indicador LED WiFi parpadea en rojoFuncionamiento de los componentes AV con el Extensor Hay ID del Extensor duplicadosActualización del Extensor con el cable de configuración Actualización de FirmwareReinicialización del Extensor Actualización del Extensor a través de un routerPronto Wireless Extender Manual de inicio EspecificacionesObservaciones RFX9400FX9400 Guide deGuidedémarragede démarrage Table des matièresMode Stand-alone autonome Mode Network réseauAvantages du mode Stand-alone autonome Avantages du mode Network réseauDéballage du Prolongateur Configuration du Prolongateur Connexion Stand-alone autonomeConnexion Network réseau Connexion filaireBranchez l’adaptateur secteur du Prolongateur Control PanelInstallation du Prolongateur Configuration du Prolongateur par un routeurPlacez le commutateur de configuration du Prolongateur sur Connexion du Prolongateur à l’équipement audio/vidéoDépannage Qu’indiquent les voyants ?Ajustement du niveau de puissance des sorties IR Il existe un conflit IPLe voyant WiFi est rouge Le voyant WiFi est rouge et clignoteIl existe des ID de Prolongateur dupliqués Configuration du Prolongateur par un routeur Mise à jour du micrologicielRéinitialisation du Prolongateur Guide de démarrage du Pronto Wireless Extender SpécificationsRemarques IFU Approbation / Safety Content RFX9400 FCC CompliancyRegulations According to R&TTE DeclarationDeclaration of ConformityDoC MarkingDeclaration of Conformity of this product can be found at IiiFrench Mise au rebut des produits en fin de vie German Entsorgung Ihres alten GerätsItalian Smaltimento di vecchi prodotti Norwegian Avhending av gamle produkterPolish Usuwanie zużytych produktów Eliminação do seu antigo produtoSlovak Likvidácia tohto produktu Slovenian Odlaganje starega izdelka3104 205