Philips RFX9400 manual Finding the Exact Location of an AV-component’s IR Receiver

Page 11

RFX9400 Starter’s Guide

•When configuring the Extender: make sure the PC is not using a fixed IP address but is using DHCP instead.

•Make sure the router is switched on. If the router is using DHCP, the Extender’s IP address cannot be determined. Make sure to use the correct network settings on the router.

The Extender cannot communicate with the wireless network

The WiFi LED is red

•Make sure that the Extender is in range of the Wireless Access Point.

•Make sure that you filled in the correct secret in the Configuration Tool.

•Add the Extender’s MAC address to the router’s list of accepted MAC addresses.

The WiFi LED is red blinking

•Check the router’s network settings and make sure that it can operate with the Extender.

•If the LED doesn’t stop blinking, unplug the power adapter, wait a few seconds, and plug it in again.

Finding the Exact Location of an AV-component’s IR Receiver

1Remove the protective tape of the Dual IR emitters.

2Set the Dual IR emitters to the minimal power level, and hold the adhesive side of one of the emitters 0.4 - 0.8 inch / 1 - 2 cm in front of the AV-component.

3Make sure the Control Panel is configured to operate with the AV-component.

4Move the emitter across the front panel of the AV-component, and at the same time, send commands with the Control Panel to the AV-component.

Take note of when the AV-component reacts to the IR signals of the emitter.

5When the AV-component reacts, position the emitter in that place.

Operating AV-components with the Extender

The AV-components do not respond to commands from the Extender

•Check if the Busy LED blinks green when you send a command with the Control Panel. If the Busy LED does not blink, the Extender is not receiving commands from the Control Panel;

•Make sure that the Control Panel is configured correctly in ProntoEdit Professional;

•Make sure that the Extender is configured correctly in the Configuration Tool and connected properly to the AV-components;

•Make sure that the switches on the Extender are set correctly.

•Make sure that the Wireless Access Point is on and configured correctly.

•Make sure that the Extender is in range of the Wireless Access Point. If the Wireless Access Point is placed higher or lower than the Extender, place the Extender’s antenna horizontally for optimum range.

There are duplicate Extender IDs

Using the Extender ID switch, assign a unique ID to each Extender in the same Pronto Network. Make sure the Control Panel is configured accordingly in ProntoEdit Professional.

You can use up to 16 different Extenders in the same Pronto Network.

ENGLISH

8

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Manual de inicio Page Starter’s Guide Contents Stand-alone Advantages Stand-alone ModeNetwork Mode Before You StartUnpacking the Extender Pronto Wireless ExtenderStand-alone Connection Configuring the ExtenderUse the default switch settings of the Extender Wireless connectionExtender will restart. After startup Configuration cable this is the crossedSet the Extender’s Configuration switch to Installing the ExtenderConfiguring the Extender through a Router Connecting the Extender to AV-equipmentWhat Do the LEDs Indicate? TroubleshootingSupport Operating AV-components with the Extender Extender cannot communicate with the wireless networkAV-components do not respond to commands from the Extender Finding the Exact Location of an AV-component’s IR ReceiverUpdating the Extender with the configuration cable Firmware UpdateResetting the Extender Busy LED blinks green when the Control Panel is not in useRemarks SpecificationsPronto Wireless Extender Starter’s Guide Contenido del paquete del Extensor ContenidoVentajas del modo Stand-alone Antes de empezarModo Stand-alone modo autónomo Modo Network modo redContenido del paquete del Extensor Conexión inalámbrica Configuración del ExtensorConexión Stand-alone Conexión NetworkMacro desde el Control Panel Abra ProntoEdit Professional en el PC Configuración del Extensor a través de un routerInstalación del Extensor Conexión del Extensor a un equipo AV¿Qué indican los indicadores LED? Detección de erroresAsistencia Hay ID del Extensor duplicados El indicador LED WiFi está iluminado en rojoEl indicador LED WiFi parpadea en rojo Funcionamiento de los componentes AV con el ExtensorActualización del Extensor a través de un router Actualización del Extensor con el cable de configuraciónActualización de Firmware Reinicialización del ExtensorObservaciones Pronto Wireless Extender Manual de inicioEspecificaciones Table des matières RFX9400FX9400 Guide deGuidedémarragede démarrageAvantages du mode Network réseau Mode Stand-alone autonomeMode Network réseau Avantages du mode Stand-alone autonomeDéballage du Prolongateur Connexion filaire Configuration du ProlongateurConnexion Stand-alone autonome Connexion Network réseauControl Panel Branchez l’adaptateur secteur du ProlongateurConnexion du Prolongateur à l’équipement audio/vidéo Installation du ProlongateurConfiguration du Prolongateur par un routeur Placez le commutateur de configuration du Prolongateur surIl existe un conflit IP DépannageQu’indiquent les voyants ? Ajustement du niveau de puissance des sorties IRIl existe des ID de Prolongateur dupliqués Le voyant WiFi est rougeLe voyant WiFi est rouge et clignote Réinitialisation du Prolongateur Configuration du Prolongateur par un routeurMise à jour du micrologiciel Remarques Guide de démarrage du Pronto Wireless ExtenderSpécifications FCC Compliancy IFU Approbation / Safety Content RFX9400Declaration Regulations According to R&TTEIii Declaration of ConformityDoCMarking Declaration of Conformity of this product can be found atNorwegian Avhending av gamle produkter French Mise au rebut des produits en fin de vieGerman Entsorgung Ihres alten Geräts Italian Smaltimento di vecchi prodottiSlovenian Odlaganje starega izdelka Polish Usuwanie zużytych produktówEliminação do seu antigo produto Slovak Likvidácia tohto produktu3104 205
Top Page Image Contents