Philips RFX9400 manual Configuring the Extender, Stand-alone Connection, Network Connection

Page 7

RFX9400 Starter’s Guide

Configuring the Extender

Note Before you start configuring the Extender, check if there are any firmware updates available in the Downloads section on www.pronto.philips.com.

Refer to the chapter ‘Firmware Update’ on page 9 for further details.

Stand-alone Connection

To configure the Stand-alone Extender:

1Plug in the Extender’s power adapter.

The Extender will start up. When start-up has finished, the Power and WiFi LEDs are green.

2Use the default switch settings of the Extender:

Stand-alone/Network	Stand-alone
Configuration switch	1
Extender ID	0

Note • If there is already an Extender with ID 0, set the Extender ID switch to an ID that is not used yet.

•If there is any interference with other products in or around the house, the Configuration switch can be set to a different RF channel.

•Make sure the same Extender ID and RF channel are used on the Extender and the Pronto Control Panel.

3Configure the Control Panel’s configuration file so that the Control Panel can work with the Extender. For more details, refer to the ProntoEdit Professional Online Help.

Network Connection

In the case of a network connection, the Extender is made part of the wireless Pronto Network. There are two ways to use the Extender in a network:

• Wired connection

Straight Ethernet Cable

Extender

Router

Control Panel

Wireless

Access Point

• Wireless connection

Extender

Control Panel

Wireless

Access Point

ENGLISH

4

Image 7

Contents Manual de inicio Page Starter’s Guide Contents Stand-alone Advantages Stand-alone ModeNetwork Mode Before You StartUnpacking the Extender Pronto Wireless ExtenderStand-alone Connection Configuring the ExtenderUse the default switch settings of the Extender Wireless connectionExtender will restart. After startup Configuration cable this is the crossedSet the Extender’s Configuration switch to Installing the ExtenderConfiguring the Extender through a Router Connecting the Extender to AV-equipmentSupport TroubleshootingWhat Do the LEDs Indicate? Operating AV-components with the Extender Extender cannot communicate with the wireless networkAV-components do not respond to commands from the Extender Finding the Exact Location of an AV-component’s IR ReceiverUpdating the Extender with the configuration cable Firmware UpdateResetting the Extender Busy LED blinks green when the Control Panel is not in usePronto Wireless Extender Starter’s Guide SpecificationsRemarks Contenido del paquete del Extensor ContenidoVentajas del modo Stand-alone Antes de empezarModo Stand-alone modo autónomo Modo Network modo redContenido del paquete del Extensor Conexión inalámbrica Configuración del ExtensorConexión Stand-alone Conexión NetworkMacro desde el Control Panel Abra ProntoEdit Professional en el PC Configuración del Extensor a través de un routerInstalación del Extensor Conexión del Extensor a un equipo AVAsistencia Detección de errores¿Qué indican los indicadores LED? Hay ID del Extensor duplicados El indicador LED WiFi está iluminado en rojoEl indicador LED WiFi parpadea en rojo Funcionamiento de los componentes AV con el ExtensorActualización del Extensor a través de un router Actualización del Extensor con el cable de configuraciónActualización de Firmware Reinicialización del ExtensorEspecificaciones Pronto Wireless Extender Manual de inicioObservaciones Table des matières RFX9400FX9400 Guide deGuidedémarragede démarrageAvantages du mode Network réseau Mode Stand-alone autonomeMode Network réseau Avantages du mode Stand-alone autonomeDéballage du Prolongateur Connexion filaire Configuration du ProlongateurConnexion Stand-alone autonome Connexion Network réseauControl Panel Branchez l’adaptateur secteur du ProlongateurConnexion du Prolongateur à l’équipement audio/vidéo Installation du ProlongateurConfiguration du Prolongateur par un routeur Placez le commutateur de configuration du Prolongateur surIl existe un conflit IP DépannageQu’indiquent les voyants ? Ajustement du niveau de puissance des sorties IRLe voyant WiFi est rouge et clignote Le voyant WiFi est rougeIl existe des ID de Prolongateur dupliqués Mise à jour du micrologiciel Configuration du Prolongateur par un routeurRéinitialisation du Prolongateur Spécifications Guide de démarrage du Pronto Wireless ExtenderRemarques FCC Compliancy IFU Approbation / Safety Content RFX9400Declaration Regulations According to R&TTEIii Declaration of ConformityDoCMarking Declaration of Conformity of this product can be found atNorwegian Avhending av gamle produkter French Mise au rebut des produits en fin de vieGerman Entsorgung Ihres alten Geräts Italian Smaltimento di vecchi prodottiSlovenian Odlaganje starega izdelka Polish Usuwanie zużytych produktówEliminação do seu antigo produto Slovak Likvidácia tohto produktu3104 205