Philips RFX9400 Configuration cable this is the crossed, Extender will restart. After startup

Page 8

RFX9400 Starter’s Guide

To configure the Network Extender:

Extender

Configuration

cable

1	Connect the Extender to the PC with the
	configuration cable (this is the crossed
	Ethernet cable enclosed).
2	Set the switches correctly:

				Stand-alone/Network	Network
				Configuration switch	2
				Extender ID	0

Note • If there is already an Extender with ID 0, set the Extender ID switch to an ID that is not used yet.

• Make sure the same Extender ID is used on the Extender and the Pronto Control Panel.

3Plug in the Extender’s power adapter.

The Extender will start up. After startup, the Power and Ethernet LEDs are green and the Busy LED is red/green blinking.

4Open the browser.

5Type the IP address of the Extender (printed on the bottom of the Extender) in the address bar of the browser.

The Configuration Tool opens in the browser.

6Follow the onscreen instructions and make sure you have the following information at hand:

•If the Extender will be connected wirelessly to the Pronto Network: the SSID and encryption settings.

•If the Extender will be operating with a fixed IP address: the IP address, netmask and default gateway.

Tip To ensure optimal performance, use a dedicated network for all Pronto communication. This makes the Pronto Network independent from other network traffic and changes in network settings.

7Disconnect the Extender from the PC.

8Connect the Extender to the Pronto Network:

•For a wired connection, connect the Extender to the router by means of a straight Ethernet cable.

•For a wireless connection, you do not need to connect any more cables.

9Set the switches correctly:

Stand-alone/Network	Network
Configuration switch	1
Extender ID	0

The Extender will restart. After startup,

•In a wired network connection, the Power and Ethernet LEDs are green and the Busy LED blinks green when it’s processing a code or a macro from the Control Panel.

•In a wireless network connection, the Power and WiFi LEDs are green and the Busy LED blinks green when it’s processing a code or a macro from the Control Panel.

5

Image 8

Contents Manual de inicio Page Starter’s Guide Contents Stand-alone Mode Network ModeBefore You Start Stand-alone AdvantagesPronto Wireless Extender Unpacking the ExtenderConfiguring the Extender Use the default switch settings of the ExtenderWireless connection Stand-alone ConnectionConfiguration cable this is the crossed Extender will restart. After startupInstalling the Extender Configuring the Extender through a RouterConnecting the Extender to AV-equipment Set the Extender’s Configuration switch toWhat Do the LEDs Indicate? TroubleshootingSupport Extender cannot communicate with the wireless network AV-components do not respond to commands from the ExtenderFinding the Exact Location of an AV-component’s IR Receiver Operating AV-components with the ExtenderFirmware Update Resetting the ExtenderBusy LED blinks green when the Control Panel is not in use Updating the Extender with the configuration cableRemarks SpecificationsPronto Wireless Extender Starter’s Guide Contenido Contenido del paquete del ExtensorAntes de empezar Modo Stand-alone modo autónomoModo Network modo red Ventajas del modo Stand-aloneContenido del paquete del Extensor Configuración del Extensor Conexión Stand-aloneConexión Network Conexión inalámbricaMacro desde el Control Panel Configuración del Extensor a través de un router Instalación del ExtensorConexión del Extensor a un equipo AV Abra ProntoEdit Professional en el PC¿Qué indican los indicadores LED? Detección de erroresAsistencia El indicador LED WiFi está iluminado en rojo El indicador LED WiFi parpadea en rojoFuncionamiento de los componentes AV con el Extensor Hay ID del Extensor duplicadosActualización del Extensor con el cable de configuración Actualización de FirmwareReinicialización del Extensor Actualización del Extensor a través de un routerObservaciones Pronto Wireless Extender Manual de inicioEspecificaciones RFX9400FX9400 Guide deGuidedémarragede démarrage Table des matièresMode Stand-alone autonome Mode Network réseauAvantages du mode Stand-alone autonome Avantages du mode Network réseauDéballage du Prolongateur Configuration du Prolongateur Connexion Stand-alone autonomeConnexion Network réseau Connexion filaireBranchez l’adaptateur secteur du Prolongateur Control PanelInstallation du Prolongateur Configuration du Prolongateur par un routeurPlacez le commutateur de configuration du Prolongateur sur Connexion du Prolongateur à l’équipement audio/vidéoDépannage Qu’indiquent les voyants ?Ajustement du niveau de puissance des sorties IR Il existe un conflit IPIl existe des ID de Prolongateur dupliqués Le voyant WiFi est rougeLe voyant WiFi est rouge et clignote Réinitialisation du Prolongateur Configuration du Prolongateur par un routeurMise à jour du micrologiciel Remarques Guide de démarrage du Pronto Wireless ExtenderSpécifications IFU Approbation / Safety Content RFX9400 FCC CompliancyRegulations According to R&TTE DeclarationDeclaration of ConformityDoC MarkingDeclaration of Conformity of this product can be found at IiiFrench Mise au rebut des produits en fin de vie German Entsorgung Ihres alten GerätsItalian Smaltimento di vecchi prodotti Norwegian Avhending av gamle produkterPolish Usuwanie zużytych produktów Eliminação do seu antigo produtoSlovak Likvidácia tohto produktu Slovenian Odlaganje starega izdelka3104 205