Philips RFX9400 manual Specifications, Pronto Wireless Extender Starter’s Guide, Remarks

Page 13

RFX9400 Starter’s Guide

3Open the ProntoEdit Professional on the PC.

4In the Tools menu, select Extender Discovery.

The Extender Discovery tool appears, with a list of all the detected Extenders in the Pronto Network.

5Select the Extender that you want to configure and click on the Configure button. The Configuration Tool opens in the browser.

6Select Firmware Update in the left navigation pane. The Firmware Update page opens.

7Follow the onscreen instructions.

ENGLISH

Specifications

The specifications and design of this product are subject to change without notice.

General	Dark grey ABS housing with poly carbonate front plate
	802.11 b/g compliant RF technology
	4 LED indications for Power, WiFi, Network and Busy
	Up to 16 extenders and 16 control panels in a system (for all modes)
	4 addressable outputs for IR emitters
	Ethernet RJ45 connection
	Rotatable RF antenna
	Positioning: freestanding or mounted in any position

Modes	Stand-alone (wireless): Similar to WiFi ad-hoc mode; no access point and
	router required
	Network (wireless): Similar to WiFi infrastructure mode; used in a system with
	a router and access point
	Network (wired via Ethernet): used in a system with a router and access point

Dimensions	3,98 x 6,18 x 1,3 inch (101,2 x 157 x 33,5 mm)

Operating temperature	32°F to 122°F (0°C to 50°C)

Infrared (IR)	IR frequency range: 25kHz-1MHz (including DC/flash codes)
	IR power out: 2 levels

Radio Frequency (RF)	802.11g at 2.4 GHz with additional proprietary protocol

Dual IR emitters	Number of IR emitters: up to 4 (2x2), emitters wired in series
	0.13 inch (3.5 mm) mono mini-jack
	Cable length: 9 ft (2.7 meters)

Mono mini-jack cables	0.13 inch (3.5 mm) mono mini-jack
	Cable length: 5 ft (1.5 meters)

Power adapter	100V-240 VAC / 50-60 Hz Power adapter (5V DC/2A output, UL-CE approved)

Pronto Wireless Extender Starter’s Guide

© Copyright 2006 Royal Philips Electronics, Interleuvenlaan 72 - 74, 3000 Leuven (Belgium)

Remarks:

All rights are reserved. Reproduction in whole or in part is prohibited without prior consent of the copyright owner. Royal Philips Electronics is not liable for omissions or for technical or editorial errors in this manual or for damages directly or indirectly resulting from the use of the Pronto Wireless Extender.

The information in this Starter’s Guide may be subject to change without prior notice.

All brand or product names are trademarks or registered trademarks of their respective companies or organizations.

10

Image 13

Contents Manual de inicio Page Starter’s Guide Contents Network Mode Stand-alone ModeBefore You Start Stand-alone AdvantagesUnpacking the Extender Pronto Wireless ExtenderUse the default switch settings of the Extender Configuring the ExtenderWireless connection Stand-alone ConnectionExtender will restart. After startup Configuration cable this is the crossedConfiguring the Extender through a Router Installing the ExtenderConnecting the Extender to AV-equipment Set the Extender’s Configuration switch toSupport TroubleshootingWhat Do the LEDs Indicate? AV-components do not respond to commands from the Extender Extender cannot communicate with the wireless networkFinding the Exact Location of an AV-component’s IR Receiver Operating AV-components with the ExtenderResetting the Extender Firmware UpdateBusy LED blinks green when the Control Panel is not in use Updating the Extender with the configuration cablePronto Wireless Extender Starter’s Guide SpecificationsRemarks Contenido del paquete del Extensor ContenidoModo Stand-alone modo autónomo Antes de empezarModo Network modo red Ventajas del modo Stand-aloneContenido del paquete del Extensor Conexión Stand-alone Configuración del ExtensorConexión Network Conexión inalámbricaMacro desde el Control Panel Instalación del Extensor Configuración del Extensor a través de un routerConexión del Extensor a un equipo AV Abra ProntoEdit Professional en el PCAsistencia Detección de errores¿Qué indican los indicadores LED? El indicador LED WiFi parpadea en rojo El indicador LED WiFi está iluminado en rojoFuncionamiento de los componentes AV con el Extensor Hay ID del Extensor duplicadosActualización de Firmware Actualización del Extensor con el cable de configuraciónReinicialización del Extensor Actualización del Extensor a través de un routerEspecificaciones Pronto Wireless Extender Manual de inicioObservaciones Table des matières RFX9400FX9400 Guide deGuidedémarragede démarrageMode Network réseau Mode Stand-alone autonomeAvantages du mode Stand-alone autonome Avantages du mode Network réseauDéballage du Prolongateur Connexion Stand-alone autonome Configuration du ProlongateurConnexion Network réseau Connexion filaireControl Panel Branchez l’adaptateur secteur du ProlongateurConfiguration du Prolongateur par un routeur Installation du ProlongateurPlacez le commutateur de configuration du Prolongateur sur Connexion du Prolongateur à l’équipement audio/vidéoQu’indiquent les voyants ? DépannageAjustement du niveau de puissance des sorties IR Il existe un conflit IPLe voyant WiFi est rouge et clignote Le voyant WiFi est rougeIl existe des ID de Prolongateur dupliqués Mise à jour du micrologiciel Configuration du Prolongateur par un routeurRéinitialisation du Prolongateur Spécifications Guide de démarrage du Pronto Wireless ExtenderRemarques FCC Compliancy IFU Approbation / Safety Content RFX9400Declaration Regulations According to R&TTEMarking Declaration of ConformityDoCDeclaration of Conformity of this product can be found at IiiGerman Entsorgung Ihres alten Geräts French Mise au rebut des produits en fin de vieItalian Smaltimento di vecchi prodotti Norwegian Avhending av gamle produkterEliminação do seu antigo produto Polish Usuwanie zużytych produktówSlovak Likvidácia tohto produktu Slovenian Odlaganje starega izdelka3104 205