Xantrex Technology ENET-XFR3 manual Baud Rate Selection, 6Jumper J2 Settings for Baud Rate

Page 40

Installation and Configuration

Baud Rate Selection

Serial transmission sends and receives data in bit streams at fixed bit rates. Both the computer and the interface must have the same bit rate setting for proper communication. The default baud rate is 9600. We recommend that you do not change this setting. If the setting must be changed, use Table 2-6to select the correct jumper positions. You will need to remove the cover to change any jumpers. See “Changing Internal Jumpers” on page 2–8.

Table 2-6Jumper J2 Settings for Baud Rate

9600BaudRateB3closed		B2closed	B1closed
4800	open	closed	closed

2400	closed	open	closed

1200	open	open	closed

600	closed	closed	open

300	open	closed	open

150	closed	open	open

75	open	open	open

2–18	TM-XR9B-01XN

Image 40

Contents Operating Manual Page XFR 1.2kW and 2.8kW Ethernet/RS-232 Interface Option Date and Revision Scope PurposeAudience Organization Conventions Used Related InformationPage Important Safety Instructions Viii Contents Operation Advanced Ethernet Administration SpecificationsCalibration Xii Figures Xiv Tables Xvi Features DescriptionFeatures and Functions Interface FeaturesProgrammable Functions Ethernet FeaturesReadback Functions Page Configuration IntroductionFor RS-232 Initial Inspection Front Panel SRQERR FLT1Item Ethernet/RS-232 Interface PCB 2Ethernet/RS-232 Interface Jumper Selections XoffProcedure for 1.2kW XFR Changing Internal JumpersProcedure for 2.8kW XFR 1Step#DescriptionActionModeConfigure for Ethernet Basic Setup Procedure EthernetBasic Setup Procedure RS-232 1StepConfiguring for Ethernet or RS-232 EthernetEthernet Communications Ethernet ConnectionLocating the Power Supply on Your Network Configuring Ethernet Bridge Installing and Using RealPort1 BackgroundRS-232Communications RS-232 Connection6Jumper J2 Settings for Baud Rate Baud Rate SelectionFlow Control Selection 7Jumper J2 Flow Control SectionRemote/Local Mode Startup Remote/Local OperationRemote Mode Operation Local Mode Operation Remote Enable REN CommandPower Supply Settings Local Lockout LLO CommandXON/XOFF RTS/CTSAdditional User Options and Settings OVP SelectionLowon TTL Shutdown PolarityHigh LOW OFF User Signals User Lines ConnectorUser Lines Signal Connector Circuit Block Diagram User Lines Cable Connection 7User Lines Cable with Ferrite BlockOperation RS-232Operation Command SyntaxManual Conventions Command Format and Parameters FormatFlo ting Point Number floa Command Strings Command TerminatorsOrder Iset 2.0A VsetCommand Summary AUXB? CMODE?DLY? ERR?FAULT? IdataIHI ILOAUXA? Command ReferenceCmode 1/ON Description AlsoRemote/Local Operation on Chapter Mask None = Unmask ALL ALL, None Command Voltage settings which are being held. See Hold command Accumulated Status, Status, and Fault Registers ASTS?PON REMACF OPFError0 #ErrorNo ErrorsIdentificationExplanation Error CodesTroubleshooting Diagnostic LEDsEthernet Mode Troubleshooting Tips 10 Ethernet Mode TipsPossibleCauses RS-232Mode Troubleshooting Tips RS-232and/or Ethernet Mode Troubleshooting TipsPage Calibration Calibration Voltage Calibration Setup Voltage Mode CalibrationVoltage Program Calibration Procedure Voltage Readback Calibration Procedure Current Calibration Setup Current Mode CalibrationCurrent Program Calibration Procedure Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Specifications 40-30 OVP600-2 40-70 600-4 Page Administration Changing the Root Password Resetting the Configuration from a Browser Resetting the Configuration to DefaultsIntroduction Viewing Port Statistics and Settings Copying the Configuration to and from a ServerViewing Network Statistics NET Interpreting LED InformationDIA Page Warranty and Product Information WarrantyDisclaimer ProductReturn Material Authorization Policy ExclusionsOut of Warranty Service Return ProcedureInformation About Your System Page Xantrex Technology Inc