IBM manual AS/400 Definition AS/400 Prompt, AS/400 Parameter Sdlclin Bit Bit Value

Page 75

 

AS/400

3651 Definition

 

AS/400 Prompt

Parameter

Statement

3651 Parameter

 

 

 

 

SSCP identifier

SSCPID

QFHOST

SSCPID

 

 

 

3651 SSCPID parameter must match the SSCPID

 

 

 

parameter specified on the AS/400 CRTCTLRTL

 

 

 

command.

 

 

 

 

Station address

STNADR

QFHOST

SDLCPOL

 

 

 

3651 SDLCPOL parameter must match the STNADR

 

 

 

parameter specified on the AS/400 CRTCTLRTL

 

 

 

command.

 

 

 

 

Switched connection

SWITCHED

QFHOST

SDLCLIN

 

 

 

Value specified for the AS/400 SWITCHED parameter

 

 

 

on the CRTCTLRTL command must match the values

 

 

 

specified for bits 2 and 3 of the 3651 SDLCLIN

 

 

 

parameter.

 

 

 

 

Note: For the AS/400 system, the 3651 QFHOST definition must specify DIRATT=NO.

The value specified for the AS/400 parameters on the CRTLINSDLC command must match the values specified on the 3651 SDLCLIN parameter.

For information about the SDLCLIN parameter, see “Specifying the SDLCLIN parameter for 3651 retail controllers”.

Specifying the SDLCLIN parameter for 3651 retail controllers

The following table describes how to coordinate values for parameters on the AS/400 CRTLINSDLC and CRTCTLRTL commands with bits that are specified for the 3651 SDLCLIN parameter.

The SDLCLIN parameter is specified as a series of 8 bits, designated 0 through 7 (01234567). The default value for the SDLCLIN parameter when used with an SDLC line is 01100001, or hex 61.

The default value for each bit is underlined in the Bit Value column.

To configure the AS/400 to a 3651 controller, use the following table.

 

 

AS/400 Parameter

 

SDLCLIN Bit

Bit Value

and Value

Notes

 

 

 

 

0

0

None

Data terminal ready. There is no equivalent

 

 

 

parameter for the AS/400 system. Specify 0 to

 

 

 

indicate that the data terminal ready (DTR) signal is

 

 

 

on when the controller is powered on, or 1 to

 

 

 

indicate that the DTR is off when the controller is

 

 

 

powered on.

 

1

None

 

 

 

 

 

This bit should be set to 1 only if the configuration

 

 

 

being defined includes IBM world trade data

 

 

 

communications equipment (DCE) in a switched

 

 

 

network.

 

 

 

 

1

0

NRZI(*NO)

Specify 1 if the data communications equipment

 

 

 

(DCE) provides the clocking or if NRZI data

 

1

NRZI(*YES)

 

encoding is used.

 

 

 

 

 

 

 

Chapter 7. Communicating with remote workstation controllers 69

Image 75
Contents ERserver Page ERserver Page Contents Troubleshooting communications problems Part 1. Getting started with AS/400 communications Version Print this topic Version Creating a line description Configuring AS/400 for communicationsCreating a network interface description Creating a network server descriptionVersion Improving wide area network performance Adjusting WAN protocols for optimum AS/400 performanceAdjusting the WAN line speed for optimum AS/400 performance Optimizing communications performanceWAN line speed considerations for IOPs Adjusting LANs for optimum communications performance Adjusting LAN lines for optimum communications performanceImproving local area network performance Improving data path performance LAN line speed considerations for IOPsAddcmne SBSDlibname/sbsname DEVdevname* MODEmodename Set up the communication entries Example Communications subsystem configurationExample Interactive subsystem configuration Communications performance considerations for batch jobsMixing interactive and batch jobs on a WAN line Setting up the AnyNet environment Performance considerations for AnyNet communicationsAnyNet communications for the AS/400 system Qusrwrk SubsystemsVersion Communications applications User written Appc applicationsDistributed data management DDM Version Communications applications Version Matching AS/400 parameters for a host system Communicating with host systemsSSAP/DSAP/remote-adapter-address Name Ssap Sapaddr Maxframe Group MaxdataRmtcpname Vtamlst Sscpname Rmtnetid Vtamlst NetidLocpwd Dfhtct Bindpwd Mode Modeent LogmodeLcllocname Dfhtct Netname Locadr LocaddrCosd Modeent COS Examples Connecting AS/400 to a host systemAS/400 Host Definition AS/400 Prompt Modd Modeent LogmodeCommunicating with host systems Version Communicating with host systems Version Configuring dependent LU requester Dlur Configuring the host controller descriptionConfiguring the device descriptions Version Adrinsert Communicating with a remote AS/400 systemAS/400 Remote AS/400 AS/400 Prompt AdptadrAS/400 Remote AS/400 AS/400 Prompt Parameter Dsap Ssap X25DCECnnnbr Netadr CnnpwdRmtnetid Lclnetid InlcnnLinkpcl Rmtcpname LclcpnameConnecting one AS/400 to another AS/400 system Version Communicating with a remote AS/400 system Version Matching AS/400 parameters for 5494 controllers Communicating with remote workstation controllersRmtnetid AS/400 5494 Prompt AS/400 Parameter Field Subfield ValueLAN RmtcpnameLinktype LAN AS/400 5494 Prompt AS/400 Parameter Field SubfieldMatching AS/400 parameters for a 5494 connected by Ethernet AS/400 5494 Prompt Parameter Field Subfield Value Version LAN Adptadr Matching AS/400 parameters for a 5494 connected by Sdlc Prompt Parameter Field Subfield AS/400 Value AS/400Field Subfield AS/400 Value Communicating with remote workstation controllers Matching AS/400 parameters for a 5494 connected by Linktype Example Connecting AS/400 to a 5494 controller connected byIBM 5494 Remote Control Unit Planning Guide, GA27-3936 Netlvl DftpktsizeLinkpcl Qllc EllcField Subfield Value AS/400 5494 PromptCommunicating with remote workstation controllers Questions 3174 AS/400 Configuration PromptMatching AS/400 parameters for 3x74 controller Matching AS/400 parameters for a 3174 controller3174 AS/400 Configuration Prompt Parameter Questions Control Unit Address Switched Short-Hold ModeMatching AS/400 parameters for a 3274 controller NRZ or Nrzi EncodingExample Connecting an AS/400 to a 3174 control unit 3274 AS/400Prompt Parameter Number Matching AS/400 parameters for 470x finance controllers Matching AS/400 parameters for finance controllersAS/400 AS/400 Prompt Parameter Macro Matching AS/400 parameters for Fbss finance controllers AS/400 AS/400 PromptMacro Parameter PC address Switched lineService access point for PC Line modeData Link Control Service access point for Host/37xx/4700Identification block and Identification number Matches the Fbss Identification numberMatching AS/400 parameters for retail controllers Example Connecting AS/400 to a finance networkAS/400 Definition AS/400 Prompt Parameter Statement Matching AS/400 parameters for 3651 retail controllersAS/400 Parameter Sdlclin Bit Bit Value AS/400 Definition AS/400 Prompt3684 AS/400 Definition Prompt Matching AS/400 parameters for 3684 retail controllers3684 AS/400 Definition Prompt Parameter SNBU*YES MODEMRATE*FULL Matching AS/400 parameters for 4680/4690 Line parameterAS/400 Parameter Linecon Bit Bit Value CNN*MP SNBU*NOCNN Exchid parameter specified on the AS/400 Crtctlrtl commandMatching AS/400 parameters for 4680/4690 Link parameter AS/400 Prompt AS/400 Parameter Line ParameterRemote node Hex Wire constant RTS?Matching AS/400 parameters for 4684 retail controllers Local node HexExamples Connecting AS/400 to a 4690 retail controller Version Communicating with remote workstation controllers Version Displaying message queues to solve communication problems Troubleshooting communications problemsQsysarb Job logs and communication problemsQpasvrp Solving communication problems using communications traceTrace option setting System service tools and communication problemsTrace full Solving communication problems using the system problem logSolving communication problems using reason codes Solving communication problems using status informationConsiderations for system tuning during error recovery Using error messages to aid in error recoveryReason Code Reason Description Reason Codes for Rejected Program Start RequestsReason Code Reason Description Advanced Peer-to-Peer Networking Networking conceptsDependent LU requester support Advanced program-to-program communicationsHigh-performance routing HPR architecture option setsInternetwork packet exchange support What is TCP/IP What is Systems Network ArchitectureDistributed data interface network Common networking standardsLocal area network standards ATM on AS/400Token-ring networks Wireless networkFrame relay networks Wide area network standardsAsynchronous communications Binary synchronous communicationsIntegrated services digital network Synchronous data link control networkIsdn data link control network Network Version
Related manuals
Manual 489 pages 47.95 Kb Manual 516 pages 58.6 Kb

AS/400 specifications

The IBM AS/400, now known as the IBM iSeries, is a midrange computer system that has been a cornerstone of enterprise computing since its introduction in 1988. Designed to provide a robust platform for business applications, the AS/400 is celebrated for its reliability, scalability, and integrated database capabilities.

One of the key features of the AS/400 is its Integrated Operating Environment, which blends hardware and software resources seamlessly. This integration allows businesses to execute diverse workloads, ranging from traditional applications to modern web-based services, all on a single platform. The operating system, OS/400 (now IBM i), offers a rich set of APIs and tools for developers, simplifying application development and management.

Another standout characteristic of the AS/400 is its built-in database, DB2 for i. This powerful relational database management system allows for efficient data handling and provides advanced features such as support for SQL, XML, and JSON, making it easier for businesses to manage their data and integrate it with other systems. The database's tight integration with the operating system enables high performance and security.

In terms of scalability, the AS/400 can accommodate small businesses as well as large enterprises, with the ability to support hundreds of users simultaneously. Its architecture allows for easy upgrades in hardware, meaning that organizations can scale their systems without replacing the entire infrastructure.

Security is another critical attribute of the AS/400. With a sophisticated security model, it offers built-in user authentication, access control, encryption, and auditing capabilities to protect data and applications from unauthorized access.

The AS/400 also supports multiple programming languages, including RPG, COBOL, Java, and PHP, giving organizations the flexibility to choose the development tools that best fit their needs. This diversity helps maintain legacy applications while also developing new ones that leverage modern technologies.

Moreover, the platform supports both traditional green-screen interfaces and modern graphical user interfaces, allowing organizations to transition smoothly into contemporary user experience paradigms.

Overall, the IBM AS/400 stands out as a resilient, flexible, and secure computing platform that enables organizations to effectively manage their business operations, streamline processes, and adapt to changing market demands. Its unique combination of integrated features and capabilities ensures that it remains relevant in today's fast-paced technology landscape.