|
| 3684 |
|
AS/400 | AS/400 | Definition |
|
Prompt | Parameter | Statement | 3684 Parameter |
|
|
|
|
Exchange | EXCHID | QVSFGLNK | SENDID |
identifier |
|
| 3684 SENDID parameter must match the last 5 digits of the |
|
|
| |
|
|
| EXCHID parameter specified on the AS/400 CRTCTLRTL |
|
|
| command. |
|
|
|
|
|
|
| RECVID |
|
|
| 3684 RECVID parameter must match the last 5 digits of the |
|
|
| EXCHID parameter specified on the AS/400 CRTLINSDLC |
|
|
| command. (This parameter is used only for switched line |
|
|
| communications.) |
|
|
|
|
Modem data | MODEMRATE | QFSFGLNK | LINECON |
rate |
|
| Value specified for the AS/400 MODEMRATE parameter on the |
|
|
| |
|
|
| CRTLINSDLC command must match the value specified for bit 5 |
|
|
| of the 3684 LINECON parameter. |
|
|
|
|
NRZI data | NRZI | QFSFGLNK | LINECON |
encoding |
|
| Value specified for the AS/400 NRZI parameter on the |
|
|
| |
|
|
| CRTLINSDLC command must match the value specified for bit 1 |
|
|
| of the 3684 LINECON parameter. |
|
|
|
|
Switched | SNBU | QFSFGLNK | LINECON |
network backup |
|
| Value specified for the AS/400 SNBU parameter on the |
|
|
| |
|
|
| CRTLINSDLC command must match the value specified for bit 4 |
|
|
| of the 3684 LINECON parameter. |
|
|
|
|
SSCP identifier | SSCPID | QVSFGLNK | SSCPID |
|
|
| 3684 SSCPID parameter must match the SSCPID parameter |
|
|
| specified on the AS/400 CRTCTLRTL command. |
|
|
|
|
Station address | STNADR | QVSFGLNK | POLCHAR |
|
|
| 3684 POLCHAR parameter must match the |
|
|
| address specified for the STNADR parameter on the AS/400 |
|
|
| CRTCTLRTL command. Allowed values are in the range 01 |
|
|
| through FE. |
|
|
|
|
Switched | SWITCHED | QFSFGLNK | LINECON |
connection |
|
| Value specified for the AS/400 SWITCHED parameter on the |
|
|
| |
|
|
| CRTCTLRTL command must match the values specified for bits |
|
|
| 2 and 3 of the 3684 LINECON parameter. |
|
|
|
|
Note: For the AS/400 system, the 3684 QVSFGLNK, QVSFCOMM, and QVSFSESN definitions must each specify
DATALNK=SDLC.
Values specified for the AS/400 parameters on the CRTCTLRTL and CRTLINSDLC commands must match the values specified on the 3684 LINECON parameter.
Specifying the LINECON parameter for 3684 retail controllers
The following table describes how to coordinate values that are specified for parameters on the AS/400 CRTLINSDLC and CRTCTLRTL commands. You must coordinate the values with bits that are specified for the 3684 LINECON parameter.
The LINECON parameter is specified as a series of 8 bits, designated 0 through 7 (01234567). The default value for the LINECON parameter when used with an SDLC line is 01000001, or hex 41.