Cisco Systems Broadband Access Center manual Installing from the Command Line

Page 22

Chapter 2 Preparing to Install Components

Installation

Step 5 Select one of the two installation types:

•Individual Components—This option enables you to install an RDU, Network Registrar extensions, the DPE, or the KDC. See these sections for the appropriate installation instructions:

–Installing the Regional Distribution Unit, page 3-2

–Installing Extensions on a Network Registrar Server, page 3-3

–Installing the Key Distribution Center, page 3-7

–Installing the Device Provisioning Engine, page 3-8

•Lab—This option enables you to install the software in a laboratory environment. See Chapter 4, “Installing in a Lab Environment” in this guide.

Step 6 Click Next. Depending on the option you selected in the preceding step, either the Installation Components screen appears, or you begin the lab installation.

Note You must select one of the displayed installation components before you can proceed with the installation.

Installing from the Command Line

To perform the initial installation procedure from the command line:

Step 1 Log into the intended BACC host as root.

Step 2 At the Solaris system prompt, change directory to your CD-ROM drive or other installation media. The installation program, setup.bin, is at the root of this drive.

Step 3 Enter this command to start the installation program:

>setup.bin -console

The installation program verifies that you have installed the required patches to the Solaris operating system. When the verification is complete, the program displays welcome information.

Step 4 Press Enter to continue. The program prompts you to choose the installation type. You can choose to install:

•Individual components

•Lab installation

Step 5 To choose individual components, enter C; or, to choose Lab installation, enter L. For example:

Choose Installation

Choose the type of BPR installation you want to install.

The Lab installation will store all components in the chosen destination.

Otherwise, you can select individual components and destinations.

Enter C for individual components or L for lab [C]:c

Cisco Broadband Access Center for Cable Installation Guide 2.7

2-8	OL-19105-01

Image 22

Contents Cisco Broadband Access Center for Cable Installation Guide Americas HeadquartersPage N T E N T S Validating Extensions Setting Up Voice Technology OL-19105-01 How This Guide Is Organized AudienceThis chapter contains the following sections Document Conventions Section Title DescriptionTo support the DPE-590 Related DocumentationRefer to these manuals for additional information To support the DPE-2115OL-19105-01 Operating System Requirements JDK Patches for SolarisHardware Requirements Network Registrar RequirementsKDC Patches Min. # Server Servers Server Class Processors MemoryTypes of Installations Min. # Recommended #Preparing to Install Components Broadband Access Center for Cable ComponentsInstallation and Startup Process Item DescriptionItem Description Item Description File System Block Size Broadband Access Center Database RequirementsThis example, the file system device is /dev/dsk/c0t0d0s4 Example output from the df command is as follows Installation ChecklistLarge File Support Installation Installation Using the Graphical User InterfaceInstalling from the Command Line Preparing to Install Components Installation OL-19105-01 Installing Components Installing the Regional Distribution Unit Installing Extensions on a Network Registrar Server Installing Extensions Enter these commands to reload the Network Registrar server Field Name DescriptionValidating Extensions Example KDC Password Installing the Key Distribution CenterLocated Installing Components Using the CLI Installing the Device Provisioning EngineProgram then asks you to confirm the directory OL-19105-01 Installing Network Registrar Extensions Is this correct y/n/q/? yes y ACME.COM Installing the Key Distribution Center Installing Components Installing Components Using the CLI Installing the Device Provisioning Engine Installing Components Installing Components Using the CLI OL-19105-01 Installing in a Lab Environment Installing in a Lab Environment Using the GUI Installing in a Lab Environment Using the CLI KDC Fqdn Dhcp Configuring Network Registrar and a Cmts Interface Cable3/0 Ip address 192.168.5.0Ip dhcp relay information option OL-19105-01 Post-Installation Activities Enabling a Network Registrar Spoofing DNS ServerSave and close the /etc/syslog.conf file Uninstalling Broadband Access CenterSyslog is now ready to receive alerts from Bacc Uninstalling Bacc from the Graphical User Interface Uninstalling Bacc from the Console ModeFollowing is displayed Press Enter to exit the programAppliance Version Solaris DPE DPE-590 DPE-2115Upgrading the RDU Before You BeginUpgrading the Solaris DPE # pkgparam CSCObpr Version Upgrading Hardware DPEs Upgrading Network Registrar Extensions Installed before you start the Bacc agentUpgrading the KDC Migrating the RDU Database Migrating from BaccWhen running this script, use this syntax MigrateDb.sh tempdirOL-19105-01 Connecting the Device Provisioning Engine Hardware DPE Setup SequenceTo do this See this section System displays this user mode prompt Configuring and Running a Terminal Emulation ProgramLogging Configuring a Device Provisioning Engine for Data Configure the current time on the DPE. For example Setting Up Voice Technology Packetcable registration policy-privacy value Debugging Example show dpe command outputControls Available Setting Up a Device Provisioning Engine Debugging Where Identifies the username Identifies the password Network Registrar Configuration File ExampleConfiguration Scripts Sample Script for Docsis Modems and ComputersSample Script for Docsis Modems and PacketCable MTAs Choose Installation Type screen Administrator’s password Alert messages InstallationSolaris Broadband Access Center Command line interface Installing components CommandsOrganization Configuration management Documentation ConventionsInstallation Summary screen 3-3,3-7,3-8,4-3 Related documents Domain Name SystemJRun process, detecting KDCSetting up DPEs Installing BACSolaris