Cisco Systems Broadband Access Center manual Installing in a Lab Environment Using the CLI

Page 45

Chapter 4 Installing in a Lab Environment

Installing in a Lab Environment Using the CLI

Field Name

Description

 

 

Kerberos Realm Name

Specifies, using a unique name, the Kerberos realm. This must match the

 

realm set at the associated components.

 

 

IP Address of Primary

Specifies the IP address of the voice technology primary DHCP server.

DHCP Server

 

 

 

IP Address of Primary DNS

Specifies the IP address of the computer which is running the primary

Server

DNS server.

 

 

IP Address of Secondary

Specifies the IP address of the voice technology secondary DHCP server.

DHCP Server

 

 

 

IP Address of Secondary

Specifies the IP address of the computer which is running the secondary

DNS Server

DNS server; if that server is being used.

 

 

Step 13 The Shared Secret Password screen appears.

Step 14 Enter and confirm the shared secret password. This password is a token that a BACC server uses to authenticate communication with other BACC servers.

Step 15 Click Next and the Lab Installation Parameters screen appears. This screen identifies the values that you have entered in the previous screens. To modify any of the values entered:

a.Click Back until the desired screen appears.

b.Make the necessary changes.

c.Click Next repeatedly until you return to this screen.

Step 16 Click Next and the lab version of BACC is installed. When installation is complete, the Installation Summary screen appears.

Step 17 Click Finish and BACC is completely installed in your lab environment.

Note You use the administrator’s user interface to configure your license keys. Refer to the Cisco Broadband Access Center for Cable Administrator’s Guide for additional information.

Caution After installation is complete, you must install your licenses and the chain of certificates or the KDC will not start.

Installing in a Lab Environment Using the CLI

The lab installation prompts for this information:

BACC destination directory

Network Registrar administrator username and password

Shared secret password

Cisco Broadband Access Center for Cable Installation Guide 2.7

 

OL-19105-01

4-3

 

 

 

Image 45
Contents Americas Headquarters Cisco Broadband Access Center for Cable Installation GuidePage N T E N T S Validating Extensions Setting Up Voice Technology OL-19105-01 Audience How This Guide Is OrganizedThis chapter contains the following sections Section Title Description Document ConventionsRefer to these manuals for additional information Related DocumentationTo support the DPE-590 To support the DPE-2115OL-19105-01 JDK Patches for Solaris Operating System RequirementsNetwork Registrar Requirements Hardware RequirementsKDC Patches Server Servers Server Class Processors Memory Min. #Min. # Recommended # Types of InstallationsBroadband Access Center for Cable Components Preparing to Install ComponentsItem Description Installation and Startup ProcessItem Description Item Description Broadband Access Center Database Requirements File System Block SizeThis example, the file system device is /dev/dsk/c0t0d0s4 Installation Checklist Example output from the df command is as followsLarge File Support Installation Using the Graphical User Interface InstallationInstalling from the Command Line Preparing to Install Components Installation OL-19105-01 Installing Components Installing the Regional Distribution Unit Installing Extensions on a Network Registrar Server Installing Extensions Field Name Description Enter these commands to reload the Network Registrar serverValidating Extensions Installing the Key Distribution Center Example KDC PasswordLocated Installing the Device Provisioning Engine Installing Components Using the CLIProgram then asks you to confirm the directory OL-19105-01 Installing Network Registrar Extensions Is this correct y/n/q/? yes y ACME.COM Installing the Key Distribution Center Installing Components Installing Components Using the CLI Installing the Device Provisioning Engine Installing Components Installing Components Using the CLI OL-19105-01 Installing in a Lab Environment Installing in a Lab Environment Using the GUI Installing in a Lab Environment Using the CLI KDC Fqdn Dhcp Interface Cable3/0 Ip address 192.168.5.0 Configuring Network Registrar and a CmtsIp dhcp relay information option OL-19105-01 Enabling a Network Registrar Spoofing DNS Server Post-Installation ActivitiesUninstalling Broadband Access Center Save and close the /etc/syslog.conf fileSyslog is now ready to receive alerts from Bacc Uninstalling Bacc from the Console Mode Uninstalling Bacc from the Graphical User InterfacePress Enter to exit the program Following is displayedSolaris DPE DPE-590 DPE-2115 Appliance VersionBefore You Begin Upgrading the RDUUpgrading the Solaris DPE # pkgparam CSCObpr Version Upgrading Hardware DPEs Installed before you start the Bacc agent Upgrading Network Registrar ExtensionsUpgrading the KDC Migrating from Bacc Migrating the RDU DatabaseMigrateDb.sh tempdir When running this script, use this syntaxOL-19105-01 Hardware DPE Setup Sequence Connecting the Device Provisioning EngineTo do this See this section Configuring and Running a Terminal Emulation Program System displays this user mode promptLogging Configuring a Device Provisioning Engine for Data Configure the current time on the DPE. For example Setting Up Voice Technology Packetcable registration policy-privacy value Example show dpe command output DebuggingControls Available Setting Up a Device Provisioning Engine Debugging Configuration Scripts Network Registrar Configuration File ExampleWhere Identifies the username Identifies the password Sample Script for Docsis Modems and ComputersSample Script for Docsis Modems and PacketCable MTAs Solaris Broadband Access Center Administrator’s password Alert messages InstallationChoose Installation Type screen Command line interface Installing components CommandsInstallation Summary screen 3-3,3-7,3-8,4-3 Configuration management Documentation ConventionsOrganization Related documents Domain Name SystemKDC JRun process, detectingInstalling BAC Setting up DPEsSolaris