Cisco Systems Broadband Access Center manual Setting Up Voice Technology

Page 67

Chapter 7 Setting Up a Device Provisioning Engine

Configuring a Device Provisioning Engine for Voice Technology

Configuring a Device Provisioning Engine for Voice Technology

This section describes those configuration activities that must be performed to properly set up a DPE to support voice technology.

Note The tips provided in this section refer to the dpe.properties file, located in the <BACC_HOME>/dpe/conf directory, for a lab installation of BAC. You change the properties specified, as indicated in the tip, to enable the described feature. If you edit the properties, you must restart the DPE.

Caution In the dpe.properties file, there should only be a single instance of each property described in these tips.

Setting Up Voice Technology

Complete these steps to set up voice technology on your DPEs.

Step 1 Enter these commands to set the FQDN for each enabled DPE interface:

interface ethernet 0 provisioning fqdn <fqdn-value>

interface ethernet 1 provisioning fqdn <fqdn-value>

Tip dpe.properties: /server/provFQDNs=FQDN[IP address]:port. This could translate, for example, into c3po.pcnet.cisco.com[10.10.10.5]:49186.

Note The FQDN is sent as the SNMPEntity in DHCP option 177 suboption 3.

Step 2 Enter these commands to configure voice technology at DPE:

packetcable registration kdc-service-key <password>

Note This is a protected mode security command, accessible only on the local console. The contents of this property are only visible when logged into the local console.

Caution The DPE password entered using this CLI command must match the corresponding password used in Keygen utility when generating Service Keys for KDC.

Tip dpe.properties: /pktcbl/regsvr/KDCServiceKey=(xx: ... xx) Where (xx: ... xx) represents a 24 byte randomly selected, colon separated, hexadecimal value; for example: 31:32:33:34:35:36:37:38:39:30:31:32:33:34:3 5:36:37:38:39:30:31:32:33:34.

Cisco Broadband Access Center for Cable Installation Guide 2.7

	OL-19105-01	7-5

Image 67

Contents Americas Headquarters Cisco Broadband Access Center for Cable Installation GuidePage N T E N T S Validating Extensions Setting Up Voice Technology OL-19105-01 How This Guide Is Organized AudienceThis chapter contains the following sections Section Title Description Document ConventionsTo support the DPE-2115 Related DocumentationRefer to these manuals for additional information To support the DPE-590OL-19105-01 JDK Patches for Solaris Operating System RequirementsHardware Requirements Network Registrar RequirementsKDC Patches Server Servers Server Class Processors Memory Min. #Min. # Recommended # Types of InstallationsBroadband Access Center for Cable Components Preparing to Install ComponentsItem Description Installation and Startup ProcessItem Description Item Description File System Block Size Broadband Access Center Database RequirementsThis example, the file system device is /dev/dsk/c0t0d0s4 Example output from the df command is as follows Installation ChecklistLarge File Support Installation Using the Graphical User Interface InstallationInstalling from the Command Line Preparing to Install Components Installation OL-19105-01 Installing Components Installing the Regional Distribution Unit Installing Extensions on a Network Registrar Server Installing Extensions Field Name Description Enter these commands to reload the Network Registrar serverValidating Extensions Example KDC Password Installing the Key Distribution CenterLocated Installing the Device Provisioning Engine Installing Components Using the CLIProgram then asks you to confirm the directory OL-19105-01 Installing Network Registrar Extensions Is this correct y/n/q/? yes y ACME.COM Installing the Key Distribution Center Installing Components Installing Components Using the CLI Installing the Device Provisioning Engine Installing Components Installing Components Using the CLI OL-19105-01 Installing in a Lab Environment Installing in a Lab Environment Using the GUI Installing in a Lab Environment Using the CLI KDC Fqdn Dhcp Interface Cable3/0 Ip address 192.168.5.0 Configuring Network Registrar and a CmtsIp dhcp relay information option OL-19105-01 Enabling a Network Registrar Spoofing DNS Server Post-Installation ActivitiesSave and close the /etc/syslog.conf file Uninstalling Broadband Access CenterSyslog is now ready to receive alerts from Bacc Uninstalling Bacc from the Console Mode Uninstalling Bacc from the Graphical User InterfacePress Enter to exit the program Following is displayedSolaris DPE DPE-590 DPE-2115 Appliance VersionUpgrading the RDU Before You BeginUpgrading the Solaris DPE # pkgparam CSCObpr Version Upgrading Hardware DPEs Upgrading Network Registrar Extensions Installed before you start the Bacc agentUpgrading the KDC Migrating from Bacc Migrating the RDU DatabaseMigrateDb.sh tempdir When running this script, use this syntaxOL-19105-01 Connecting the Device Provisioning Engine Hardware DPE Setup SequenceTo do this See this section System displays this user mode prompt Configuring and Running a Terminal Emulation ProgramLogging Configuring a Device Provisioning Engine for Data Configure the current time on the DPE. For example Setting Up Voice Technology Packetcable registration policy-privacy value Debugging Example show dpe command outputControls Available Setting Up a Device Provisioning Engine Debugging Sample Script for Docsis Modems and Computers Network Registrar Configuration File ExampleConfiguration Scripts Where Identifies the username Identifies the passwordSample Script for Docsis Modems and PacketCable MTAs Command line interface Installing components Commands Administrator’s password Alert messages InstallationSolaris Broadband Access Center Choose Installation Type screenRelated documents Domain Name System Configuration management Documentation ConventionsInstallation Summary screen 3-3,3-7,3-8,4-3 OrganizationKDC JRun process, detectingSetting up DPEs Installing BACSolaris