Brocade Communications Systems 53-1002580-01 manual Fiber Optic Devices

Page 38

3 Fiber Optic Devices

Fiber Optic Devices

An optional Gigabit SFP transceiver or 100BASE-FX SFP transceiver can be used for a backbone connection between switches, or for connecting to a high-speed server.

Each single-mode fiber port requires 9/125 micron single-mode fiber optic cable with an LC connector at both ends. Each multimode fiber optic port requires 50/125 or 62.5/125 micron multimode fiber optic cabling with an LC connector at both ends.

CAUTION

This switch uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

NOTE

When selecting a fiber SFP device, considering safety, please make sure that it can function at a temperature that is not less than the recommended maximum operational temperature of the product. You must also use an approved Laser Class 1 SFP transceiver.

1.Remove and keep the LC port’s rubber cover. When not connected to a fiber cable, the rubber cover should be replaced to protect the optics.

2.Check that the fiber terminators are clean. You can clean the cable plugs by wiping them gently with a clean tissue or cotton ball moistened with a little ethanol. Dirty fiber terminators on fiber cables will impair the quality of the light transmitted through the cable and lead to degraded performance on the port.

3.Connect one end of the cable to the LC port on the switch and the other end to the LC port on the other device. Since LC connectors are keyed, the cable can be attached in only one orientation.

FIGURE 21 MAKING CONNECTIONS TO SFP TRANSCEIVERS

4.As a connection is made, check the Link LED on the switch corresponding to the port to be sure that the connection is valid.

24

Brocade 6910 Ethernet Access Switch Hardware Installation Guide

 

53-1002580-01

Image 38
Contents Brocade 6910 Ethernet Access Switch Brocade Communications Systems, Incorporated Contents Appendix a Troubleshooting Appendix D 53-1002580-01 Figures Page Tables 53-1002580-01 Audience About This DocumentThis chapter Supported hardware and softwareRelated publications Bold textGetting technical help or reporting errors About This Document Introduction OverviewOverview Switch Architecture Network Management OptionsDescription of Hardware SFP Slots10/100/1000BASE-T Management Port The Craft Interface Alarm Interface Port10/100/1000BASE-T Ports Console PortLED Power Supply Sockets Description of Hardware Mbps Port Status / SFP LEDs 1~12Description of Hardware Installing the Switch Selecting a SiteEthernet Cabling Equipment ChecklistPackage Contents Rack Mounting MountingDesktop or Shelf Mounting Attaching the Brackets Installing an Optional SFP Transceiver Grounding the ChassisConnecting to a Power Source Grounding PointConnecting DC Power Remove both power cords before servicingTop View Front View Rear View DC Plug Connections Connecting to the Console Port Connecting AC PowerWiring Map for Serial Cable Serial Cable WiringConnecting to the Alarm Port Wiring Map for Alarm CableMinor Alarm Connecting to the Alarm Port Making Network Connections Connecting Network DevicesConnecting to PCs, Servers, Hubs and Switches Twisted-Pair DevicesFiber Optic Devices Making Connections to SFP TransceiversIn-Band Access TroubleshootingDiagnosing Switch Indicators 53-1002580-01 10BASE-T/100BASE-TX Pin Assignments CablesTwisted-Pair Cable and Pin Assignments Straight-Through Wiring Crossover WiringCable Testing for Existing Category 5 Cable 1000BASE-T Pin AssignmentsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsSpecifications Physical CharacteristicsSwitch Features Compliances Management FeaturesStandards Safety ImmunityEnglish / French Mise EN GardeMise EN Garde Connecteurs RJ-45 conformes aux normes FCC Device Remove both power cords before servicing Page German / Spanish / Chinese VorsichtPrecaución Vorsicht Gefahr Oder umfallen kann Spanish only NotaPrecaución Spanish only Pueda sobrepasar los 65 ºC 149 ºF Para la Categoría 5 RJ45 y los cables de fibra óptica Spanish only Chinese Traditional Kg 7.5 lbs 重量 ISO/IEC 8802-3 CSMA/CD 使用托架安裝套件所附的螺絲,將托架安裝至裝置。 使用四顆機架安裝螺絲 未隨附 ,將裝置安裝至機架。 300 253 。 將外接的饋電及電源接地 / 回線,連接至下圖所示的 DC 插頭 交換器隨附 。在機箱正面、DC 電源接線板的上 18 AWG、標示 VW-1 及額定最小 90C。 Chinese Traditional Taiwan Bsmi Statement Chinese Simplified China-CCC Warning statementsChinese Simplified Glossary 10BASE-TCSMA/CD LED UTP Index Numerics53-1002580-01