Brocade Communications Systems 53-1002580-01 manual 300 253 。

Page 70

E Chinese (Traditional)

備註

機箱接地

 

 

在開啟交換器的電源前,請依下列說明,將交換器確實接地。

 

1.

確定要安裝至交換器的機架有正確接地,並符合 ETSI ETS

 

 

300 253

 

2.

確定機架上的接地點有良好的電氣連接 ( 沒有經過漆面或

 

 

絕緣表面處理 )

 

中斷交換器所有電源線的連接。

 

連接電源

 

交換器機箱內接 0 V 電源。此電路連接至交換器背面的單孔接

 

地端。為提供良好的連接,此端子周圍的表面區域,沒有經

 

過漆面處理。將 18 AWG 銅絞線連接至交換器上的接地端。

 

接著將接地線連接至機架上的接地點。

 

 

 

 

注意

未中斷所有供電連接前,不得移除接地連接。

 

 

 

 

 

 

注意

連接電源

 

 

這些交換器支援 AC/DC 雙電源供應器。

 

連接 DC 電源

 

使用 20-60 Vdc 電源時,外部 DC 電源供應器,必須連接至前

 

面板左側的 DC 電源接頭。DC 輸入 (DC 電源 ) 必須運用加強

 

絕緣,以隔離 AC 電源。

 

 

 

危險

危險

備註

備註

維修前,請拔出兩條電源線。

連接 DC 插頭、或接通交換器電源前,務必從電路器關閉,或 從電源匯流排中斷饋電線的電源。

為了在 DC 電源供應器與交換器之間,提供適當的電路保護, 所有中間接線及電路系統的額定值,應至少能承受此交換器

最高額定值兩倍以上的負載 ( 請參閱第 34 頁的 〈電源供應〉 )

對於 DC 系統,請使用至少 18 AWG ( 美國線規 ) 的接地線。 18 AWG 接地線應連接至主管機關核准的壓接式接頭 ( 機箱上 有提供 ),並使用適合的工具進行壓接。壓接式接頭必須能緊

固機殼上的兩個接地螺絲。對於接地片,請使用 UL-listed Panduit 壓接式接頭 (P/N LCD6-10A)及兩顆 10-32PPH1/2

螺絲,將壓接式接頭固定至機箱。接地位置在緊鄰接地符號 的機箱側邊。

Brocade 6910 Ethernet Access Switch Hardware Installation Guide

56

53-1002580-01

 

Image 70
Contents Brocade 6910 Ethernet Access Switch Brocade Communications Systems, Incorporated Contents Appendix a Troubleshooting Appendix D 53-1002580-01 Figures Page Tables 53-1002580-01 Audience About This DocumentThis chapter Supported hardware and softwareRelated publications Bold textGetting technical help or reporting errors About This Document Introduction OverviewOverview Switch Architecture Network Management OptionsDescription of Hardware SFP Slots10/100/1000BASE-T Management Port The Craft Interface Alarm Interface Port10/100/1000BASE-T Ports Console PortLED Power Supply Sockets Description of Hardware Mbps Port Status / SFP LEDs 1~12Description of Hardware Installing the Switch Selecting a SitePackage Contents Equipment ChecklistEthernet Cabling Desktop or Shelf Mounting MountingRack Mounting Attaching the Brackets Installing an Optional SFP Transceiver Grounding the ChassisConnecting to a Power Source Grounding PointConnecting DC Power Remove both power cords before servicingTop View Front View Rear View DC Plug Connections Connecting to the Console Port Connecting AC PowerWiring Map for Serial Cable Serial Cable WiringConnecting to the Alarm Port Wiring Map for Alarm CableMinor Alarm Connecting to the Alarm Port Making Network Connections Connecting Network DevicesConnecting to PCs, Servers, Hubs and Switches Twisted-Pair DevicesFiber Optic Devices Making Connections to SFP TransceiversDiagnosing Switch Indicators TroubleshootingIn-Band Access 53-1002580-01 Twisted-Pair Cable and Pin Assignments Cables10BASE-T/100BASE-TX Pin Assignments Straight-Through Wiring Crossover WiringCable Testing for Existing Category 5 Cable 1000BASE-T Pin AssignmentsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsSpecifications Physical CharacteristicsSwitch Features Standards Management FeaturesCompliances Safety ImmunityEnglish / French Mise EN GardeMise EN Garde Connecteurs RJ-45 conformes aux normes FCC Device Remove both power cords before servicing Page German / Spanish / Chinese VorsichtPrecaución Vorsicht Gefahr Oder umfallen kann Spanish only NotaPrecaución Spanish only Pueda sobrepasar los 65 ºC 149 ºF Para la Categoría 5 RJ45 y los cables de fibra óptica Spanish only Chinese Traditional Kg 7.5 lbs 重量 ISO/IEC 8802-3 CSMA/CD 使用托架安裝套件所附的螺絲,將托架安裝至裝置。 使用四顆機架安裝螺絲 未隨附 ,將裝置安裝至機架。 300 253 。 將外接的饋電及電源接地 / 回線,連接至下圖所示的 DC 插頭 交換器隨附 。在機箱正面、DC 電源接線板的上 18 AWG、標示 VW-1 及額定最小 90C。 Chinese Traditional Taiwan Bsmi Statement Chinese Simplified China-CCC Warning statementsChinese Simplified Glossary 10BASE-TCSMA/CD LED UTP Index Numerics53-1002580-01