Brocade Communications Systems 53-1002580-01 manual Connecteurs RJ-45 conformes aux normes FCC

Page 51

Dangers D

CAUTION

Do not plug a phone jack connector into an RJ-45 port. This will damage the switch. Use

 

only twisted-pair cables with RJ-45 connectors that conform to FCC standards.

 

 

MISE EN GARDE

Ne raccordez aucun connecteur pour prise téléphonique à un port RJ-45. Le commutateur

 

risque d'être endommagé. Utilisez uniquement des câbles à paires torsadées avec

 

connecteurs RJ-45 conformes aux normes FCC.

 

 

CAUTION

This switch uses lasers to transmit signals over fiber optic cable. The lasers are compliant

 

with the requirements of a Class 1 Laser Product and are inherently eye safe in normal

 

operation. However, you should never look directly at a transmit port when it is powered

 

on.

 

 

MISE EN GARDE

Ce commutateur utilise des lasers pour transmettre les signaux sur un câble en fibre

 

optique. Les lasers sont conformes aux exigences d'un produit laser de Classe 1 et sont

 

par conséquent sans risque pour les yeux en condition de fonctionnement normal.

 

Toutefois, vous ne devez jamais regarder directement un port de transmission lorsqu'il

 

est en activité.

 

 

CAUTION

Each wire pair must be attached to the RJ-45 connectors in a specific orientation.

 

 

MISE EN GARDE

Chaque paire doit être raccordée au connecteur RJ-45 dans un ordre parfaitement

 

déterminé.

 

 

Dangers

A danger calls your attention to a possible hazard that can cause injury or death. The following are the dangers used in this manual.

Un danger attire votre attention sur un risque possible de blessure ou de décès. Ci-dessous, vous trouverez les dangers utilisés dans ce manuel.

DANGER

Laser Radiation. Do Not View Directly with Optical Instruments. Class 1M Laser Products.

 

 

DANGER

Rayonnement de laser. Ne regardez pas directement avec les instruments optiques.

 

Produits de laser de la classe 1M.

 

 

 

 

DANGER

All fiber optic interfaces use Class 1 lasers.

 

 

DANGER

Toutes les interfaces en fibres optiques utilisent des lasers de classe 1.

 

 

 

 

DANGER

Installation and removal of the unit must be carried out by qualified personnel only.

 

 

DANGER

L'installation et la dépose de l'unité doivent être confiées uniquement à du personnel

 

qualifié.

 

 

Brocade 6910 Ethernet Access Switch Hardware Installation Guide

37

53-1002580-01

 

Image 51
Contents Brocade 6910 Ethernet Access Switch Brocade Communications Systems, Incorporated Contents Appendix a Troubleshooting Appendix D 53-1002580-01 Figures Page Tables 53-1002580-01 Supported hardware and software About This DocumentThis chapter AudienceBold text Related publicationsGetting technical help or reporting errors About This Document Overview IntroductionOverview Network Management Options Switch ArchitectureSFP Slots Description of HardwareConsole Port Alarm Interface Port10/100/1000BASE-T Ports 10/100/1000BASE-T Management Port The Craft InterfaceLED Description of Hardware Mbps Port Status / SFP LEDs 1~12 Power Supply SocketsDescription of Hardware Selecting a Site Installing the SwitchEquipment Checklist Package ContentsEthernet Cabling Mounting Desktop or Shelf MountingRack Mounting Attaching the Brackets Grounding the Chassis Installing an Optional SFP TransceiverGrounding Point Connecting to a Power SourceRemove both power cords before servicing Connecting DC PowerTop View Front View Rear View DC Plug Connections Connecting AC Power Connecting to the Console PortSerial Cable Wiring Wiring Map for Serial CableWiring Map for Alarm Cable Connecting to the Alarm PortMinor Alarm Connecting to the Alarm Port Twisted-Pair Devices Connecting Network DevicesConnecting to PCs, Servers, Hubs and Switches Making Network ConnectionsMaking Connections to SFP Transceivers Fiber Optic DevicesTroubleshooting Diagnosing Switch IndicatorsIn-Band Access 53-1002580-01 Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Crossover Wiring Straight-Through Wiring1000BASE-T Pin Assignments Cable Testing for Existing Category 5 CableFiber Standards Adjusting Existing Category 5 Cabling to Run 1000BASE-TPhysical Characteristics SpecificationsSwitch Features Management Features StandardsCompliances Immunity SafetyMise EN Garde English / FrenchMise EN Garde Connecteurs RJ-45 conformes aux normes FCC Device Remove both power cords before servicing Page Vorsicht German / Spanish / ChinesePrecaución Vorsicht Gefahr Oder umfallen kann Nota Spanish onlyPrecaución Spanish only Pueda sobrepasar los 65 ºC 149 ºF Para la Categoría 5 RJ45 y los cables de fibra óptica Spanish only Chinese Traditional Kg 7.5 lbs 重量 ISO/IEC 8802-3 CSMA/CD 使用托架安裝套件所附的螺絲,將托架安裝至裝置。 使用四顆機架安裝螺絲 未隨附 ,將裝置安裝至機架。 300 253 。 將外接的饋電及電源接地 / 回線,連接至下圖所示的 DC 插頭 交換器隨附 。在機箱正面、DC 電源接線板的上 18 AWG、標示 VW-1 及額定最小 90C。 Chinese Traditional Taiwan Bsmi Statement China-CCC Warning statements Chinese SimplifiedChinese Simplified 10BASE-T GlossaryCSMA/CD LED UTP Numerics Index53-1002580-01