Extron electronic MLC 52 manual Application Diagrams, Device Drivers, System Requirements

Page 10

Device Drivers

In order for the MLC 52 to control a switcher, projector, or other display device via IR or RS-232 communication, it must have drivers loaded for the devices it will control. Drivers can be obtained in the following ways:

•IR or an RS-232 driver files can be installed from a disc, downloaded at www.extron.com, or downloaded from Extron via the driver subscription feature within the MLC 52 configuration program.

The drivers are saved on your computer in a folder located at C:\Program Files or Program Files (x86)\Extron\Driver2. You can then upload the desired drivers to the MLC via the MLC 52 configuration software.

•IR commands can be captured from the IR remote control of a device through

IR Learning or IR data transfer to create a driver. When a driver is created, it can be added to the configuration program so that the commands can be used to configure the MLC to control the device (see Configuring the MLC 52 Using IR on page 15).

System Requirements

The minimum PC system requirements for installing the configuration software are:

•Intel® Pentium® III 750 MHz processor

•Microsoft® Windows® XP or higher

•Microsoft.NET Framework 2.0 or higher

•128 MB of RAM

•50 MB of available hard disk space

Application Diagrams

RS-232 Control

Projector with

Internal Speakers

VGA

Stereo Audio

Video

Stereo Audio

DVD

PC

Figure 1. Application Diagram for an MLC 52 RS

	IS	P	L
D		P
			OFF


ON
			PC
VOL			VIDEO
VOL
			52
			MLC

Extron

MLC 52 RS

Basic MediaLink Controller with IR and RS-232 display control

MLC 52 MediaLink Controllers • Introduction

4

Image 10

Contents MLC 52 Series Safety Instructions Safety Instructions English Chinese Simplified（简体中文）FCC Class a Notice TrademarksConventions Used in this Guide Specifications AvailabilitySoftware Commands NotificationsContents Serial Communication Reference InformationAbout the MLC 52 Series MediaLink Controllers IntroductionAbout this Guide ModelsEuropean models Standard FeaturesMK models Options and Accessories MLC 52 Configuration SoftwareDevice Drivers Application DiagramsSystem Requirements MLC 52 RS VC Rear Panel and Cable Connections Installation ConfigurationMLC MLC 52 RS MK VC MLC 52 RS MK and MLC 52 RS MK VC Rear Views MLC 52 RS EU and MLC 52 RS EU VC Rear ViewsInstallation Steps Replacing the Faceplate US Models Only Replacing Button Labels Screws to Remove from the MLC FaceplateRemoving and Replacing a Button Label Wiring the Control Connector Wiring for RS-232 Control RS Models OnlyWiring for IR Control Wiring an IRL Wiring an IRLWiring the Power Connector Configuring the MLC 52 Using IRConfiguring Using IR Data Transfer IR Beaming Data Transfer Order in which the Buttons Blink during Data Transfer Percent Complete MLC 52 Models MLC 52 VC Models Buttons LitConfiguring Using IR Learning Activation of LEDs During Button ConfigurationRemoving IR Commands from a Button Setting Up Button Macros Using IR Setting Up an MLC 52 VC Model with an Extron Amplifier Wiring the VC PortRequirements for the MLC 52 VC Extron MPAMounting the MLC Configuring the MLC 52 IR VC and MLC 52 RS VC Vol ButtonsPreparing the Site Mounting the MLC to an Electrical Box Mounting the MLC to a Decora Mounting Bracket Mounting the MLC 52 to an Electrical BoxMounting the MLC to a Wall or Furniture Mounting an MLC 52 to a Decora Mounting BracketOperation Front Panel FeaturesSwitch modes Buttons on the Front PanelFront Panel Components MLC 52 IR and RS MLC 52 IR VC and RS VCMLC 52 RS Mkmlc 52 RS MK VC Mm TRS Cable for the Configuration Port Selecting Inputs Input Selection Buttons on the MLC 52 Front PanelResetting Locking the Front Panel Executive ModeApplication 1 Using Multiple Sources with an MLC Special ApplicationsExamples of Projector Remote Control Types a and B Programming Buttons for an IR Controlled SystemProjector remote control type a application Standard MLC 52 models with a type a remote controlProjector remote control type B application MLC 52 VC models with a type a remote controlStandard MLC 52 with a type B remote control Turn Power OFF? Yes Press Again No Please Wait Programming RGB inputs projector remote control type a Programming video inputs projector remote control type a Projector Remote Type a Using the PC button RGB Using the Video button S-video or composite videoProgramming RGB inputs projector remote control type B Programming video inputs projector remote control type BProjector Remote Type B Using the PC button RGB Using the MLC 52/DVCM 50 Configuration Program Configuration PortsSerial Communication Installing the Software from the DVD Extron Software DVD ScreenDownloading and Installing the Software from the Website Control Software Button on Download Center ScreenStarting the Configuration Program Select a Comm Port TabMLC 52/DVCM 50 Configuration Program Window Loading Extron Drivers Loading the serial RS-232 driversDownloading IR drivers from the DVD Selecting the MLC 52/DVCM 50 IR Driver PackageIR Device Drivers Package List To download a single driver Saving a Single Driver to the ComputerDownloading drivers from the website Device Drivers ScreenEntering MLC 62 Driver Search Criteria Error Responses Using SIS CommandsUsing the Command and Response Table Host-to-Controller CommunicationsSymbol Definitions Command and Response Table for SIS Commands Reference Information Part Numbers and AccessoriesIncluded Parts Replacement Part Number Included PartsOptional Accessories Recommended CablesMounting an Electrical Box Templates for MLC 52 and MLC 52 VC US Models Attaching an Electrical Box to a Wall StudMLC MLC 52 VC Surface CUT-OUT Area For Furniture Mount 50 8.90 cm 40 cm Extron Warranty

Related manuals

Manual 124 pages 24.39 Kb