Extron electronic MLC 52 manual Programming video inputs projector remote control type a

Page 46

3.Program the input selection command “A” from the RGB 2 input selection button on the projector remote control into memory block 2 of the MLC 52 PC button:

a.Press the PC button on the MLC front panel. The button blinks, indicating that the MLC is ready to learn the command. On the rear panel, the second LED from the bottom flashes.

b.Within 5 seconds (while the PC button on the MLC 52 is blinking), press the RGB 2 button on the remote control. The MLC learns command “A” for RGB 2.

4.Program the input selection command “B” from the RGB 1 input selection button on the projector remote control into memory block 3 of the MLC 52 PC button:

a.Press the PC button on the MLC front panel. The button blinks, indicating that the MLC is ready to learn the command. On the rear panel, the third LED from the bottom flashes.

b.Within 5 seconds (while the PC button on the MLC 52 is blinking), press the RGB 1 button on the projector remote control. The MLC learns command “B” for RGB 1.

5.Program the input selection command “B” from the RGB 2 input selection button on the projector remote control into memory block 4 of the MLC 52 PC button:

a.Press the PC button on the MLC front panel. The button blinks, indicating that the MLC is ready to learn the command. On the rear panel, the fourth LED from the bottom flashes.

b.Within 5 seconds (while the PC button on the MLC 52 is blinking), press the RGB 2 button on the remote control. The MLC learns command “B” for RGB 2.

6.If finished programming the MLC 52 buttons, return configuration DIP switch 1 to its Off (down) position, and test the system.

If you want to program video input selection at this time, proceed to “Programming video inputs — projector remote control type A.”

Programming video inputs — projector remote control type A

COMPUTER VIDEO

VIDEO AUDIO A/V

MUTE MUTE MUTE

MENUENTER

CONT/ COL/

SIZE CENTER BRT TINT

SHARP

PHASE

ASPECT

RATIO

PROJECTOR

ON

OFF

VOL

PC

 

VOL

VIDEO

 

 

MLC 52

Command 1: Computer The button should be in input switch mode.

Command 2: Video The button should be in input switch mode.

Projector Remote Control Type B

Figure 37. Programming MLC 52 Input Selection Buttons from a Projector Remote Control Type A

MLC 52 MediaLink Controllers • Special Applications

40

Image 46
Contents MLC 52 Series Safety Instructions Safety Instructions English Chinese Simplified(简体中文)FCC Class a Notice TrademarksConventions Used in this Guide Specifications AvailabilitySoftware Commands NotificationsContents Serial Communication Reference InformationAbout the MLC 52 Series MediaLink Controllers IntroductionAbout this Guide ModelsEuropean models Standard FeaturesMK models Options and Accessories MLC 52 Configuration SoftwareDevice Drivers Application DiagramsSystem Requirements MLC 52 RS VC Rear Panel and Cable Connections Installation ConfigurationMLC MLC 52 RS MK VC MLC 52 RS MK and MLC 52 RS MK VC Rear Views MLC 52 RS EU and MLC 52 RS EU VC Rear ViewsInstallation Steps Replacing the Faceplate US Models Only Replacing Button Labels Screws to Remove from the MLC FaceplateRemoving and Replacing a Button Label Wiring the Control Connector Wiring for RS-232 Control RS Models OnlyWiring for IR Control Wiring an IRL Wiring an IRLWiring the Power Connector Configuring the MLC 52 Using IRConfiguring Using IR Data Transfer IR Beaming Data Transfer Order in which the Buttons Blink during Data Transfer Percent Complete MLC 52 Models MLC 52 VC Models Buttons LitConfiguring Using IR Learning Activation of LEDs During Button ConfigurationRemoving IR Commands from a Button Setting Up Button Macros Using IR Setting Up an MLC 52 VC Model with an Extron Amplifier Wiring the VC PortRequirements for the MLC 52 VC Extron MPAMounting the MLC Configuring the MLC 52 IR VC and MLC 52 RS VC Vol ButtonsPreparing the Site Mounting the MLC to an Electrical Box Mounting the MLC to a Decora Mounting Bracket Mounting the MLC 52 to an Electrical BoxMounting the MLC to a Wall or Furniture Mounting an MLC 52 to a Decora Mounting BracketOperation Front Panel FeaturesSwitch modes Buttons on the Front PanelFront Panel Components MLC 52 IR and RS MLC 52 IR VC and RS VCMLC 52 RS Mkmlc 52 RS MK VC Mm TRS Cable for the Configuration Port Selecting Inputs Input Selection Buttons on the MLC 52 Front PanelResetting Locking the Front Panel Executive ModeApplication 1 Using Multiple Sources with an MLC Special ApplicationsExamples of Projector Remote Control Types a and B Programming Buttons for an IR Controlled SystemProjector remote control type a application Standard MLC 52 models with a type a remote controlProjector remote control type B application MLC 52 VC models with a type a remote controlStandard MLC 52 with a type B remote control Turn Power OFF? Yes Press Again No Please Wait Programming RGB inputs projector remote control type a Programming video inputs projector remote control type a Projector Remote Type a Using the PC button RGB Using the Video button S-video or composite videoProgramming RGB inputs projector remote control type B Programming video inputs projector remote control type BProjector Remote Type B Using the PC button RGB Using the MLC 52/DVCM 50 Configuration Program Configuration PortsSerial Communication Installing the Software from the DVD Extron Software DVD ScreenDownloading and Installing the Software from the Website Control Software Button on Download Center ScreenStarting the Configuration Program Select a Comm Port TabMLC 52/DVCM 50 Configuration Program Window Loading Extron Drivers Loading the serial RS-232 driversDownloading IR drivers from the DVD Selecting the MLC 52/DVCM 50 IR Driver PackageIR Device Drivers Package List To download a single driver Saving a Single Driver to the ComputerDownloading drivers from the website Device Drivers ScreenEntering MLC 62 Driver Search Criteria Error Responses Using SIS CommandsUsing the Command and Response Table Host-to-Controller CommunicationsSymbol Definitions Command and Response Table for SIS Commands Reference Information Part Numbers and AccessoriesIncluded Parts Replacement Part Number Included PartsOptional Accessories Recommended CablesMounting an Electrical Box Templates for MLC 52 and MLC 52 VC US Models Attaching an Electrical Box to a Wall StudMLC MLC 52 VC Surface CUT-OUT Area For Furniture Mount 50 8.90 cm 40 cm Extron Warranty
Related manuals
Manual 124 pages 24.39 Kb