Extron electronic manual Front Panel Components, MLC 52 IR and RS MLC 52 IR VC and RS VC

Page 34

•Power mode: The two Display buttons at the top of the front panel, labeled On and Off, are permanently in power mode. This mode is similar to input mode. The two Display buttons are mutually exclusive; if you press one, the other one becomes unlit.

NOTE: You can also set up button macros using IR (see Setting Up Button Macros Using IR on page 20).

To change the switch mode of a button (except the display buttons), you must use the configuration software (see the configuration program help file for the procedure).

Front Panel Components

The following diagrams show the front panels of the standard and VC versions of all MLC 52 models.

NOTE: The front panel buttons are prelabeled for convenience. You can relabel them using the other labels that are provided (see Replacing Button Labels on page 10 for the relabeling procedure).

5

4

	DISPLAY				DISPLAY
ON	OFF	1	VOLUME	ON	OFF
			VOLUME

VOL	PC	VCR	PC
VOL		2
		2
VOL	VIDEO	DVD
	VIDEO	DVD

	MLC 52				MLC 52



3			3
	MLC 52 IR and RS				MLC 52 IR VC and RS VC

Figure 23. MLC 52 and MLC 52 VC Front Panels

1

2

MLC 52 MediaLink Controllers • Operation

28

Image 34

Contents MLC 52 Series Safety Instructions Safety Instructions English Chinese Simplified（简体中文）FCC Class a Notice TrademarksConventions Used in this Guide Specifications AvailabilitySoftware Commands NotificationsContents Serial Communication Reference InformationAbout the MLC 52 Series MediaLink Controllers IntroductionAbout this Guide ModelsEuropean models Standard FeaturesMK models Options and Accessories MLC 52 Configuration SoftwareDevice Drivers Application DiagramsSystem Requirements MLC 52 RS VC Rear Panel and Cable Connections Installation ConfigurationMLC MLC 52 RS MK VC MLC 52 RS MK and MLC 52 RS MK VC Rear Views MLC 52 RS EU and MLC 52 RS EU VC Rear ViewsInstallation Steps Replacing the Faceplate US Models Only Replacing Button Labels Screws to Remove from the MLC FaceplateRemoving and Replacing a Button Label Wiring the Control Connector Wiring for RS-232 Control RS Models OnlyWiring for IR Control Wiring an IRL Wiring an IRLWiring the Power Connector Configuring the MLC 52 Using IRConfiguring Using IR Data Transfer IR Beaming Data Transfer Order in which the Buttons Blink during Data Transfer Percent Complete MLC 52 Models MLC 52 VC Models Buttons LitConfiguring Using IR Learning Activation of LEDs During Button ConfigurationRemoving IR Commands from a Button Setting Up Button Macros Using IR Setting Up an MLC 52 VC Model with an Extron Amplifier Wiring the VC PortRequirements for the MLC 52 VC Extron MPAMounting the MLC Configuring the MLC 52 IR VC and MLC 52 RS VC Vol ButtonsPreparing the Site Mounting the MLC to an Electrical Box Mounting the MLC to a Decora Mounting Bracket Mounting the MLC 52 to an Electrical BoxMounting the MLC to a Wall or Furniture Mounting an MLC 52 to a Decora Mounting BracketOperation Front Panel FeaturesSwitch modes Buttons on the Front PanelFront Panel Components MLC 52 IR and RS MLC 52 IR VC and RS VCMLC 52 RS Mkmlc 52 RS MK VC Mm TRS Cable for the Configuration Port Selecting Inputs Input Selection Buttons on the MLC 52 Front PanelResetting Locking the Front Panel Executive ModeApplication 1 Using Multiple Sources with an MLC Special ApplicationsExamples of Projector Remote Control Types a and B Programming Buttons for an IR Controlled SystemProjector remote control type a application Standard MLC 52 models with a type a remote controlProjector remote control type B application MLC 52 VC models with a type a remote controlStandard MLC 52 with a type B remote control Turn Power OFF? Yes Press Again No Please Wait Programming RGB inputs projector remote control type a Programming video inputs projector remote control type a Projector Remote Type a Using the PC button RGB Using the Video button S-video or composite videoProgramming RGB inputs projector remote control type B Programming video inputs projector remote control type BProjector Remote Type B Using the PC button RGB Using the MLC 52/DVCM 50 Configuration Program Configuration PortsSerial Communication Installing the Software from the DVD Extron Software DVD ScreenDownloading and Installing the Software from the Website Control Software Button on Download Center ScreenStarting the Configuration Program Select a Comm Port TabMLC 52/DVCM 50 Configuration Program Window Loading Extron Drivers Loading the serial RS-232 driversDownloading IR drivers from the DVD Selecting the MLC 52/DVCM 50 IR Driver PackageIR Device Drivers Package List To download a single driver Saving a Single Driver to the ComputerDownloading drivers from the website Device Drivers ScreenEntering MLC 62 Driver Search Criteria Error Responses Using SIS CommandsUsing the Command and Response Table Host-to-Controller CommunicationsSymbol Definitions Command and Response Table for SIS Commands Reference Information Part Numbers and AccessoriesIncluded Parts Replacement Part Number Included PartsOptional Accessories Recommended CablesMounting an Electrical Box Templates for MLC 52 and MLC 52 VC US Models Attaching an Electrical Box to a Wall StudMLC MLC 52 VC Surface CUT-OUT Area For Furniture Mount 50 8.90 cm 40 cm Extron Warranty

Related manuals

Manual 124 pages 24.39 Kb