Extron electronic MLC 52 manual Turn Power OFF? Yes Press Again No Please Wait

Page 44

Application 2: Controlling Projectors that Require Power Off Confirmation

Some projectors controlled via IR require the Power Off button on the hand-held remote control to be pressed twice to turn off the projector. These projectors usually present

a prompt (similar to the one shown below) on the image, instructing you to press the Power Off button again to confirm your intent to power off the projector. (If the projector is controlled via RS-232, this prompt is usually not displayed.)

Turn Power OFF?

Yes: Press Again No: Please Wait

Figure 35. Typical Projector Power Off Confirmation Prompt

The MLC 52 can be configured so that the projector Power Off button does not need to be pressed twice for confirmation. Using the macro mode feature, you can send two power off commands sequentially from a single press of the MLC Off button.

To configure the MLC Off button to issue both a power off and a power off confirmation command:

1.Ensure that power is applied to the MLC 52.

2.Set configuration DIP switch 1 on the rear panel to On (up).

ON

 

 

 

1

2

3

4

3.Program the first two command memory blocks (commands 1 and 2) on the MLC Off button with a projector off command (see Configuring Using IR Learning on page 18 for procedures).

 

DISPLAY

ON

OFF

VOL

PC

 

VOL

VIDEO

 

MLC 52

Command 1: Off

Command 2: Off

Set button to macro mode.

Figure 36. Programming the Off Button for a Projector that Requires a Confirmation

MLC 52 MediaLink Controllers • Special Applications

38

Page 43 Page 45
Image 44
Page 43 Page 45
Contents MLC 52 Series Safety Instructions Safety Instructions English Chinese Simplified（简体中文）FCC Class a Notice TrademarksSpecifications Availability Software CommandsConventions Used in this Guide NotificationsContents Serial Communication Reference InformationIntroduction About this GuideAbout the MLC 52 Series MediaLink Controllers ModelsMK models Standard FeaturesEuropean models Options and Accessories MLC 52 Configuration SoftwareSystem Requirements Application DiagramsDevice Drivers MLC 52 RS VC MLC Installation ConfigurationRear Panel and Cable Connections MLC 52 RS MK VC MLC 52 RS MK and MLC 52 RS MK VC Rear Views MLC 52 RS EU and MLC 52 RS EU VC Rear ViewsInstallation Steps Replacing the Faceplate US Models Only Replacing Button Labels Screws to Remove from the MLC FaceplateRemoving and Replacing a Button Label Wiring the Control Connector Wiring for RS-232 Control RS Models OnlyWiring for IR Control Wiring an IRL Wiring an IRLConfiguring Using IR Data Transfer IR Beaming Configuring the MLC 52 Using IRWiring the Power Connector Data Transfer Order in which the Buttons Blink during Data Transfer Percent Complete MLC 52 Models MLC 52 VC Models Buttons LitConfiguring Using IR Learning Activation of LEDs During Button ConfigurationRemoving IR Commands from a Button Setting Up Button Macros Using IR Setting Up an MLC 52 VC Model with an Extron Amplifier Wiring the VC PortRequirements for the MLC 52 VC Extron MPAPreparing the Site Configuring the MLC 52 IR VC and MLC 52 RS VC Vol ButtonsMounting the MLC Mounting the MLC to an Electrical Box Mounting the MLC to a Decora Mounting Bracket Mounting the MLC 52 to an Electrical BoxMounting the MLC to a Wall or Furniture Mounting an MLC 52 to a Decora Mounting BracketFront Panel Features Switch modesOperation Buttons on the Front PanelFront Panel Components MLC 52 IR and RS MLC 52 IR VC and RS VCMLC 52 RS Mkmlc 52 RS MK VC Mm TRS Cable for the Configuration Port Selecting Inputs Input Selection Buttons on the MLC 52 Front PanelResetting Locking the Front Panel Executive ModeApplication 1 Using Multiple Sources with an MLC Special ApplicationsExamples of Projector Remote Control Types a and B Programming Buttons for an IR Controlled SystemProjector remote control type a application Standard MLC 52 models with a type a remote controlProjector remote control type B application MLC 52 VC models with a type a remote controlStandard MLC 52 with a type B remote control Turn Power OFF? Yes Press Again No Please Wait Programming RGB inputs projector remote control type a Programming video inputs projector remote control type a Projector Remote Type a Using the PC button RGB Using the Video button S-video or composite videoProgramming RGB inputs projector remote control type B Programming video inputs projector remote control type BProjector Remote Type B Using the PC button RGB Serial Communication Configuration PortsUsing the MLC 52/DVCM 50 Configuration Program Installing the Software from the DVD Extron Software DVD ScreenDownloading and Installing the Software from the Website Control Software Button on Download Center ScreenStarting the Configuration Program Select a Comm Port TabMLC 52/DVCM 50 Configuration Program Window Loading Extron Drivers Loading the serial RS-232 driversDownloading IR drivers from the DVD Selecting the MLC 52/DVCM 50 IR Driver PackageIR Device Drivers Package List To download a single driver Saving a Single Driver to the ComputerDownloading drivers from the website Device Drivers ScreenEntering MLC 62 Driver Search Criteria Using SIS Commands Using the Command and Response TableError Responses Host-to-Controller CommunicationsSymbol Definitions Command and Response Table for SIS Commands Part Numbers and Accessories Included Parts Replacement Part NumberReference Information Included PartsOptional Accessories Recommended CablesMounting an Electrical Box Templates for MLC 52 and MLC 52 VC US Models Attaching an Electrical Box to a Wall StudMLC MLC 52 VC Surface CUT-OUT Area For Furniture Mount 50 8.90 cm 40 cm Extron Warranty
Related manuals
Manual 124 pages 24.39 Kb
Top Page Image Contents