Extron electronic manual Pin Function RS-232 RS-422 RS-485, IPL T S Series Installation

Page 20

Installation and Operation, cont’d

Factory default protocol for the control interface is:

•RS-232

•9600 baud

•no parity

•8 data bits

•1 stop bit

•pacing = 0 ms

•handshaking = off

Communication to an attached device can be done through the IPL T S Series device’s default Web pages or by using the Extron Simple Instruction Set (SIS™) commands.

The rear panel 9-pin D connector COM ports have the following pin assignments:

Pin	Function	RS-232	RS-422	RS-485
2	Receive Data/Receive Data -	RX	RX-	Data -
3	Transmit Data/ Transmit Data -	TX	TX-	(pins 2 + 3 tied)

5	Signal Ground	GND	GND	GND

7	Request to Sent/Transmit Data +	RTS	TX+	Data +
8	Clear to Send/Receive Data +	CTS	RX+	(pins 7 + 8 tied)

NThe IPL T S1 uses RS-232 only.

When using RS-485 with the connections indicated above, Data + can connect to either pin 7 or pin 8, and Data - can connect to either pin 2 or pin 3.

For RS-232 communication, pins 7 and 8 (RTS and CTS) are optional.

	5	1
	9	6
	9-Pin D Connector
Pin Locations, Female
IPL T S2			IPL T S6
Connectors			Connectors
COM1	COM2	COM3	COM4 COM5	COM6
					7/8”
TX RX	TX RX	TX RX	TX RX TX RX	TX RX	(22 mm)
					Heat

	Shrink	1/8”
	Shrink	(3 mm)
		(3 mm)
		3/16”
		(5 mm) Max.

5-pole Captive Screw

Connector

Transmit Receive Ground Transmit Receive

Transmit Receive Ground Transmit Receive

Transmit Receive Ground Transmit Receive

Figure 2-10 — 5-pin captive screw assignments

2-8 IPL T S Series • Installation

Image 20

Contents IPL T S Series IP Link Ethernet Control InterfacesPrecautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschIPL T S Series FCC Class a NoticeIi IPL T S Series Quick Start IPL T S Series IPL T S Series Quick Start QS-1QS-2 IPL T S Series Quick Start Table of Contents Table of Contents, cont’d One About the IPL T S Series Interface IntroductionAbout This Manual Features IPL T S6Introduction, cont’d Two Installation and Operation Installation OverviewIPL T S Series Installation and Operation Mounting the IPL T S InterfaceMounting Type Kit PN Mounting optionsRack mounting an IPL T S Series interface Installation and Operation, cont’d Furniture or projector mounting Rear Panel Features and Cabling Mounting the interfacePower Section A-AEthernet/LAN Serial CommunicationIPL T S Series Installation Pin Function RS-232 RS-422 RS-485Identification Front panel indicatorsOperation Resetting the unit 13 IPL T S4 front panelReset Mode Comparison/Summary Mode Activation ResultInstallation and Operation, cont’d Three Connection and Configuration Connecting the HardwareIPL T S Series Connection and Configuration Ethernet connectionSetting the Internet Protocol IP Address IPL T S4Connection and Configuration, cont’d Setting the IP address using Global ConfiguratorSetting the IP address using embedded Web pages Setting the IP address in Global ConfiguratorInternet Protocol TCP/IP Properties dialog box Setting the IP address using the ARP command Example C\arp -s 10.13.197.64 00-05-A6-00-30-5FConfiguration using Global Configurator Click the Download GCSW3XX.exe buttonConfiguration using Embedded Web Pages Global ConfiguratorConnecting via the Web server pages Web server Password dialog boxSystem Status ConfigurationSystem Settings 12 System Settings screen Port SettingsPasswords Email AlertsFirmware Upgrade File ManagementConfiguration using DataViewer Click the Control Software icon19 Communication Setup dialog box Four Using the command/response table Communication and ControlProgrammer’s Guide for Telnet and Web Browsers IPL T S Series Communication and ControlIPL T S Series Communication and Control Password information Copyright informationError responses Communication Bidirectional serial data portSeries Communication and Control Ascii to Decimal Conversion Table X!* X2%, X2, X2&, X2*CP WX! %2A X2% %2CX2 %2CX2 X2%, X2, X2&, X2 X!*X2CY X!*X3,X3!CFX5,X5#,X2 X6 TCSeries Communication and Control Ethernet data portFirmware version, part number and information requests X1! Series X4%, X4, X4&CR WX4%%2CX4%2CX4&CR IprX4%,X4,X4& X4%CRX4, X4& X4%SM X4%,X7,X4&SM WX4%%2CX7%2CX4&SM X1$ ,X1% ,X7# ,X7$ CMIpmX1$ ,X1% ,X7# ,X7$ X1& ,X1% CM WX1$ %2CX1% CM X1@CN X1@ X1#CT X1#X2@ X6$,X1$ EB WX6$%2CX1$EB Bmd X6$,X1$ X6$ EB X6$,X1$ Password and security settings X3# CA X3# CU WX3# CU X5@Remap port designations WMTDirectories ECJ WCJEDF Stream files via Telnet or RS-232 ZQQQ Server Side Includes SSI CustomizationCustom Web pages Server Side Include Using a Remote SIS command Query stringCode examples Example6b Browser view of previous Html source code URL encoding Reserved charactersUnsafe characters Serial pass-through redirect modeAdvanced Serial Port Control Direct port access ports 2001 through IPL T S2Serial Bridging Hardware connectionSerial bridge configuration IPL T S4Data connections TroubleshootingPower connections IPL T S Series Communication and Control Communication and Control, cont’d Specifications, Part Numbers, Accessories IPL T S Series Specifications, Part Numbers, Accessories Specifications, Part Numbers, AccessoriesSpecifications EMI/EMC Part Numbers and Accessories Optional accessoriesIncluded parts Replacement part Number Accessories Part numberAppendix B IPL T S Series Glossary GlossaryGlossary IPL T S Series Glossary Extron’s Warranty Extron USA West

Related manuals

Manual 6 pages 25.01 Kb