Extron electronic ISM 482 manual Optional Output Connection, Ethernet Connection

Page 15

Optional Output Connection

FDVI output connector (optional) — If the optional DVI output card is installed, connect a DVI/DFP-compatible video display to this DVI connector. This connector outputs the image selected for output 1 only.

NOTE: For output resolutions with less than 1024 pixels horizontally, the optional DVI output’s true horizontal resolution is limited to 1024 pixels. For the

1365 x 1024, 1080p, and 1080i output resolutions, the optional DVI output’s true horizontal resolution is limited to 1280 pixels. The DVI card outputs all other selected resolutions normally (see the table on page 20).

Ethernet Connection

GEthernet port — If desired, connect the switcher to an Ethernet LAN or WAN via this RJ-45 connector. Ethernet control allows the operator to control the switcher from a remote location. When connected to an Ethernet LAN or WAN, the switcher can be accessed and operated from a computer running a standard Internet browser.

Ethernet connection indicators — The Link and Act LEDs indicate the status of the Ethernet connection.

The Link LED indicates that the switcher is properly connected to an Ethernet LAN. This LED should light steadily.

The Act LED indicates transmission of data packets on the RJ-45 connector. This LED should flicker as the switcher communicates.

Cabling and RJ-45 connector wiring

It is vital that your Ethernet cables be the correct cables, and that they be properly terminated with the correct pinout.

Choosing a network cable

Ethernet links use Category (CAT) 3, 4, 5, 5e, or 6, unshielded twisted pair (UTP) or shielded twisted pair (STP) cables, terminated with RJ-45 connectors. Ethernet cables are limited to 328 feet (100 m).

NOTES:

•Do not use standard telephone cables. Telephone cables will not support Ethernet or Fast Ethernet.

•Do not stretch or bend cables. Transmission errors can occur.

The cable used depends on your network speed. The ISM supports both 10 Mbps (10Base-T — Ethernet) and 100 Mbps (100Base-T — Fast Ethernet), half-duplex and full- duplex, Ethernet connections.

•10Base-T Ethernet requires, at a minimum, CAT 3 UTP or STP cable.

•100Base-T Fast Ethernet requires, at a minimum, CAT 5 UTP or STP cable.

ISM 482 Integrated Scaling Matrix Switcher • Installation

9

Page 14 Page 16
Image 15
Page 14 Page 16
Contents No Photo Available yet ISMSafety Instructions Specifications Availability Conventions Used in this Guide FCC Class a NoticeNotifications  X! *X1@* X1%* X1** X1 CE Software CommandsContents Reference Information Switcher SoftwareHtml Operation Ethernet ConnectionAbout the Switcher IntroductionAbout This Guide ISM Inputs FeaturesISM 482 Integrated Scaling Matrix Switcher Introduction Rack Mounting InstallationMounting the Switcher Tabletop PlacementInput Connections Cabling and Rear Panel ViewsConnections for Various Input Video Formats BNC Output Connections for Rgbhv and Rgbs Video Standard Output ConnectionsChoosing a network cable Cabling and RJ-45 connector wiringOptional Output Connection Ethernet ConnectionPin RS-232 Function ConfigurationWiring the network cable RS-232 ConnectionOperation Front Panel Controls and IndicatorsOutput Buttons and LEDs Video/Audio Selection Button and LEDsSelecting an input Recalling a user presetInput Buttons, LEDs, and Label Window Front panel input label windowPicture Adjustment Buttons Black/Mute Button and LEDsAuto imaging an input LCD Display Adjustment KnobsPower Front Panel OperationsExtron Electronics ISM 60-425-01 Version Menu System OverviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuSync Type and Polarity submenu 000 Advanced Configuration MenuBlanking submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenuReset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenuSave Preset submenu User Presets menuExit menu Erase Preset submenuPicture Adjustments Flowchart Picture AdjustmentsFront Panel Security Lockout Flowchart Front Panel Security Lockout Executive ModeIP Information IP Information FlowchartOptimizing the Video Troubleshooting Setting up a DVD sourceOptimizing the Audio General Checks Specific ProblemsRS-232 Link Programming GuideEthernet Link Default Address= Hdtv SymbolsInput and Output Video Type Switcher-Initiated MessagesPower-up Ties Creation@BrtX1 Test Pattern RGB DelayPAL Film Mode Automated AdjustmentsHost-to-Switcher Instructions Switcher Error ResponsesUsing the Command and Response Table Command and Response Table for SIS Commands Horizontal size TintBrightness ContrastCommand and Response Table for SIS Commands Freeze User presetsDetail filter S-video and composite video inputs Auto MemoriesAudio mute Front panel security lockout Executive modeVerbose mode Set audio gain and attenuationInformation requests ResetsCommand and Response Table for IP SIS Commands Symbol definitionsCommand and response table PAL film mode RGB delayScaler output settings Enhanced modeMemory backup Switcher Software Installing the SoftwareControl Software for Windows Software Operation via Ethernet Ethernet protocol settingsIf you selected a comm port, proceed to step Using the Control ProgramWindows Control Program Window Button-Label Generator Using the Help ProgramExtron Button-Label Generator Window Using the SoftwareLoading the Startup Control Html OperationEnter Network Password Blacking out the Screen and Muting the Audio Changing the RGB DelayControl Creating a TieOutputting a Test Pattern Using Blue-Only ModeExecutive Mode Freezing the OutputAdministration Fields System ConfigurationHardware Address field ISM IP Settings FieldsISM IP Address field ISM Name fieldFile Management File ManagementO Configuration Input ConfigurationOutput Resolution, Rate, Sync Format, and Polarity Output resolution Output rateOutput format Polarity Drop Box Output polarityOpening and Closing the Switcher Maintenance ModificationsRemoving the ISM Cover ISM Firmware Chip Locations Installing a Firmware UpgradeDVI Output Card Connector Opening and Socket J14 Installing a DVI Output CardOutput DVI Board Installation Cabling Ethernet ConnectionDetermining Default Addresses Pinging to Determine the Switcher IP AddressPinging to Determine the Web IP Address Connecting as a Telnet Client Telnet TipsOpen Close Escape character and Esc keyLocal echo Set carriage return-line feedIncluded Parts Optional AccessoriesReference Information Part NumbersBulk cable Cables and ConnectorsAssorted connectors Button LabelsPage USA, Canada, South America Central America Japan Extron Warranty
Related manuals
Manual 105 pages 36.37 Kb
Top Page Image Contents