Extron electronic ISM 482 Button Labels, Cables and Connectors, Bulk cable, Assorted connectors

Page 80

Cables and Connectors

When using signals with a scanning frequency of 15-125 kHz and running distances of 100 feet or more, use high resolution BNC cables to achieve maximum performance.

Bulk cable

Extron Part

 

RG6/Super High Resolution Cable

Part Number

 

 

RG6 bulk , 500’ (150m), single conductor

22-098-02

 

 

RG6-1 bulk , 1000’ (300m), single conductor

22-098-03

 

 

 

 

MHR-5 Cable (Non-plenum)

Part Number

 

 

MHR-5 bulk, 500’ (150m)

22-020-02

 

 

MHR-5 bulk, 1000’ (300m)

22-020-03

 

 

 

 

MHR-5p (Plenum) Cable

Part Number

 

 

MHR-5P bulk, 500’ (150m)

22-103-02

 

 

MHR-5P bulk, 1000’ (300m)

22-103-03

 

 

Assorted connectors

BNC Connectors

Part Number

BNC male, mini HR crimp connectors, qty. 50

100-250-01

 

 

BNC male RG6 crimp connectors, qty. 50

100-260-01

 

 

Pre-cut cables

MHR-5 cable is used for RGBHV cable runs. It can also be used for composite video, S-video, or RGsB. All Extron BNC cables have male connectors on both ends. A plenum version of the MHR cable is also available.

MHR-5 Cable

Part Number

 

 

MHR-5 BNC (6’ /1.8 meters to 300’ /90.0 meters)

26-260-xx

NOTE: Bulk cable in lengths up to 5000 feet (1524 meter) rolls is available with or without connectors.

Button Labels

Eight sets of button labels are provided on the next page. If desired, cut them out of the manual, write the applicable button information in each button area, and place them in the switcher’s label window.

ISM 482 Integrated Scaling Matrix Switcher • Reference Information 74

Image 80
Contents ISM No Photo Available yetSafety Instructions Notifications Specifications Availability Conventions Used in this GuideFCC Class a Notice Software Commands  X! *X1@* X1%* X1** X1 CEContents Switcher Software Html OperationEthernet Connection Reference InformationAbout This Guide About the SwitcherIntroduction ISM Features InputsISM 482 Integrated Scaling Matrix Switcher Introduction Installation Mounting the SwitcherTabletop Placement Rack MountingCabling and Rear Panel Views Input ConnectionsConnections for Various Input Video Formats Standard Output Connections BNC Output Connections for Rgbhv and Rgbs VideoCabling and RJ-45 connector wiring Optional Output ConnectionEthernet Connection Choosing a network cableConfiguration Wiring the network cableRS-232 Connection Pin RS-232 FunctionFront Panel Controls and Indicators OperationVideo/Audio Selection Button and LEDs Output Buttons and LEDsRecalling a user preset Input Buttons, LEDs, and Label WindowFront panel input label window Selecting an inputAuto imaging an input Picture Adjustment ButtonsBlack/Mute Button and LEDs Adjustment Knobs PowerFront Panel Operations LCD DisplayMenu System Overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuSync Type and Polarity submenu Advanced Configuration Menu 000Blue-Only Mode and Edge Smoothing submenu RGB Delay submenuTest Pattern submenu Blanking submenuEnhanced Mode submenu Pixel Phase submenuPAL Film Mode submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture Adjustments Picture Adjustments FlowchartFront Panel Security Lockout Executive Mode Front Panel Security Lockout FlowchartIP Information Flowchart IP InformationOptimizing the Video Optimizing the Audio TroubleshootingSetting up a DVD source Specific Problems General ChecksProgramming Guide RS-232 LinkDefault Address Ethernet LinkSymbols = HdtvSwitcher-Initiated Messages Power-upTies Creation Input and Output Video Type@BrtX1 RGB Delay PAL Film ModeAutomated Adjustments Test PatternUsing the Command and Response Table Host-to-Switcher InstructionsSwitcher Error Responses Command and Response Table for SIS Commands Tint BrightnessContrast Horizontal sizeCommand and Response Table for SIS Commands User presets Detail filter S-video and composite video inputsAuto Memories FreezeFront panel security lockout Executive mode Verbose modeSet audio gain and attenuation Audio muteResets Information requestsCommand and response table Command and Response Table for IP SIS CommandsSymbol definitions RGB delay Scaler output settingsEnhanced mode PAL film modeMemory backup Control Software for Windows Switcher SoftwareInstalling the Software Ethernet protocol settings Software Operation via EthernetUsing the Control Program If you selected a comm port, proceed to stepWindows Control Program Window Using the Help Program Button-Label GeneratorUsing the Software Extron Button-Label Generator WindowHtml Operation Loading the Startup ControlEnter Network Password Changing the RGB Delay ControlCreating a Tie Blacking out the Screen and Muting the AudioUsing Blue-Only Mode Executive ModeFreezing the Output Outputting a Test PatternSystem Configuration Administration FieldsISM IP Settings Fields ISM IP Address fieldISM Name field Hardware Address fieldFile Management File ManagementInput Configuration O ConfigurationOutput Resolution, Rate, Sync Format, and Polarity Output format Output resolutionOutput rate Output polarity Polarity Drop BoxMaintenance Modifications Opening and Closing the SwitcherRemoving the ISM Cover Installing a Firmware Upgrade ISM Firmware Chip LocationsInstalling a DVI Output Card DVI Output Card Connector Opening and Socket J14Output DVI Board Installation Ethernet Connection CablingPinging to Determine the Web IP Address Determining Default AddressesPinging to Determine the Switcher IP Address Open Connecting as a Telnet ClientTelnet Tips Escape character and Esc key Local echoSet carriage return-line feed CloseOptional Accessories Reference InformationPart Numbers Included PartsCables and Connectors Assorted connectorsButton Labels Bulk cablePage Extron Warranty USA, Canada, South America Central America Japan
Related manuals
Manual 105 pages 36.37 Kb