Extron electronic ISM 482 manual Black/Mute Button and LEDs, Picture Adjustment Buttons

Page 20

Auto imaging an input

The auto imaging feature automatically sizes and centers the selected input to fill the screen. Initiate the auto imaging feature for a specific input by pressing and holding the appropriate input button until the LCD displays the message Auto Image Input

#n, releasing the input button, and then pressing and releasing the input button again. The LCD displays AutoSizing and Centering Please Wait... until the operation is complete.

Alternatively, using the menu system, you can set this feature to apply the Auto Image adjustments to every input as it is selected (see Auto Imaging and Auto Memories submenu on page 22).

Black/Mute Button and LEDs

EBlack/Mute button and LEDs — The Black/Mute button switches the selected output(s) to a black screen and/or muted audio. The black screen and/or mute audio is deselected when a new input is selected.

Picture Adjustment Buttons

FThe picture adjustment buttons select individual image adjustments that are adjusted

using the Adjust and Adjust knobs (I). The LEDs above these buttons light when the button is pressed (see Picture Adjustments on page 25).

Color/Tint control button — The Color/Tint button selects the display color and tint adjustments. The color adjustment range is from 0 to 127. The tint adjustment range is from 0 to 255.

NOTE: The Color/Tint control affects only composite video and S-video inputs.

Brightness/Contrast control button — The Brightness/Contrast button selects the display brightness and contrast adjustments. The adjustment range for both brightness and contrast is from 0 to 63.

Size control button — The Size button selects the display size adjustment. The adjustment range depends on the output resolution selected.

Center control button — The Center button selects the display centering adjustment. The adjustment range depends on the output resolution selected.

Filter control (Detail) button — The Detail button selects the display image detail (sharpness) adjustment. There are separate horizontal and vertical filters for RGB and component video. There is a single filter for S-video and composite video. The sharpness adjustment compensates for long cable runs.

•For RGB and component video, the Adjust knob controls the horizontal filter and the Adjust knob controls the vertical filter. The adjustment range for the horizontal filter is from 0 to 3. The adjustment range for the vertical filter is from 0 to 7.

•For S-video and composite video, either Adjust knob controls the filter setting. The range of the adjustment is from 0 to 7.

ISM 482 Integrated Scaling Matrix Switcher • Operation

14

Page 19 Page 21
Image 20
Page 19 Page 21
Contents ISM No Photo Available yetSafety Instructions Notifications Specifications Availability Conventions Used in this GuideFCC Class a Notice Software Commands  X! *X1@* X1%* X1** X1 CEContents Switcher Software Html OperationEthernet Connection Reference InformationAbout This Guide About the SwitcherIntroduction ISM Features InputsISM 482 Integrated Scaling Matrix Switcher Introduction Installation Mounting the SwitcherTabletop Placement Rack MountingCabling and Rear Panel Views Input ConnectionsConnections for Various Input Video Formats Standard Output Connections BNC Output Connections for Rgbhv and Rgbs VideoCabling and RJ-45 connector wiring Optional Output ConnectionEthernet Connection Choosing a network cableConfiguration Wiring the network cableRS-232 Connection Pin RS-232 FunctionFront Panel Controls and Indicators OperationVideo/Audio Selection Button and LEDs Output Buttons and LEDsRecalling a user preset Input Buttons, LEDs, and Label WindowFront panel input label window Selecting an inputAuto imaging an input Picture Adjustment ButtonsBlack/Mute Button and LEDs Adjustment Knobs PowerFront Panel Operations LCD DisplayMenu System Overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuSync Type and Polarity submenu Advanced Configuration Menu 000Blue-Only Mode and Edge Smoothing submenu RGB Delay submenuTest Pattern submenu Blanking submenuEnhanced Mode submenu Pixel Phase submenuPAL Film Mode submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture Adjustments Picture Adjustments FlowchartFront Panel Security Lockout Executive Mode Front Panel Security Lockout FlowchartIP Information Flowchart IP InformationOptimizing the Video Optimizing the Audio TroubleshootingSetting up a DVD source Specific Problems General ChecksProgramming Guide RS-232 LinkDefault Address Ethernet LinkSymbols = HdtvSwitcher-Initiated Messages Power-upTies Creation Input and Output Video Type@BrtX1 RGB Delay PAL Film ModeAutomated Adjustments Test PatternUsing the Command and Response Table Host-to-Switcher InstructionsSwitcher Error Responses Command and Response Table for SIS Commands Tint BrightnessContrast Horizontal sizeCommand and Response Table for SIS Commands User presets Detail filter S-video and composite video inputsAuto Memories FreezeFront panel security lockout Executive mode Verbose modeSet audio gain and attenuation Audio muteResets Information requestsCommand and response table Command and Response Table for IP SIS CommandsSymbol definitions RGB delay Scaler output settingsEnhanced mode PAL film modeMemory backup Control Software for Windows Switcher SoftwareInstalling the Software Ethernet protocol settings Software Operation via EthernetUsing the Control Program If you selected a comm port, proceed to stepWindows Control Program Window Using the Help Program Button-Label GeneratorUsing the Software Extron Button-Label Generator WindowHtml Operation Loading the Startup ControlEnter Network Password Changing the RGB Delay ControlCreating a Tie Blacking out the Screen and Muting the AudioUsing Blue-Only Mode Executive ModeFreezing the Output Outputting a Test PatternSystem Configuration Administration FieldsISM IP Settings Fields ISM IP Address fieldISM Name field Hardware Address fieldFile Management File ManagementInput Configuration O ConfigurationOutput Resolution, Rate, Sync Format, and Polarity Output format Output resolutionOutput rate Output polarity Polarity Drop BoxMaintenance Modifications Opening and Closing the SwitcherRemoving the ISM Cover Installing a Firmware Upgrade ISM Firmware Chip LocationsInstalling a DVI Output Card DVI Output Card Connector Opening and Socket J14Output DVI Board Installation Ethernet Connection CablingPinging to Determine the Web IP Address Determining Default AddressesPinging to Determine the Switcher IP Address Open Connecting as a Telnet ClientTelnet Tips Escape character and Esc key Local echoSet carriage return-line feed CloseOptional Accessories Reference InformationPart Numbers Included PartsCables and Connectors Assorted connectorsButton Labels Bulk cablePage Extron Warranty USA, Canada, South America Central America Japan
Related manuals
Manual 105 pages 36.37 Kb
Top Page Image Contents