Extron electronic ISM 482 Installation, Mounting the Switcher, Tabletop Placement, Rack Mounting

Page 11

Installation

This section describes:

Mounting the Switcher

Cabling and Rear Panel Views

Configuration

Mounting the Switcher

Four uninstalled rubber feet are included with the switcher. If you are going to rack mount the switcher, mount it before you cable it (see “Rack Mounting,” below), and do not install the rubber feet. If you are not rack mounting the switcher, see “Tabletop Pacement,” below.

Tabletop Placement

For tabletop placement, install the self-adhesive rubber feet/pads (provided) onto the four corners of the bottom of the switcher.

Rack Mounting

UL guidelines

The following Underwriters Laboratories (UL) requirements pertain to the installation of the switcher into a rack (see figure 2 on the next page).

Elevated operating ambient temperature — If the equipment is installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, install the switcher in an environment compatible with the maximum ambient temperature (Tma = +122 °F, +50°C) specified by Extron.

Reduced air flow — Install the equipment in a rack so that the amount of air flow required for safe operation of the equipment is not compromised.

Mechanical loading — Mount the equipment in the rack so that a hazardous condition is not achieved due to uneven mechanical loading.

Circuit overloading — Connect the equipment to the supply circuit and consider the effect that circuit overloading might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted equipment. Pay particular attention to supply connections other than direct connections to the branch circuit (that is, use of power strips).

Mounting instructions

To rack mount the switcher, use two screws on each end of the switcher to attach the switcher to the rack (see figure 2).

ISM 482 Integrated Scaling Matrix Switcher • Installation

5

Image 11
Contents No Photo Available yet ISMSafety Instructions Notifications Specifications Availability Conventions Used in this GuideFCC Class a Notice  X! *X1@* X1%* X1** X1 CE Software CommandsContents Reference Information Switcher SoftwareHtml Operation Ethernet ConnectionAbout This Guide About the SwitcherIntroduction ISM Inputs FeaturesISM 482 Integrated Scaling Matrix Switcher Introduction Rack Mounting InstallationMounting the Switcher Tabletop PlacementInput Connections Cabling and Rear Panel ViewsConnections for Various Input Video Formats BNC Output Connections for Rgbhv and Rgbs Video Standard Output ConnectionsChoosing a network cable Cabling and RJ-45 connector wiringOptional Output Connection Ethernet ConnectionPin RS-232 Function ConfigurationWiring the network cable RS-232 ConnectionOperation Front Panel Controls and IndicatorsOutput Buttons and LEDs Video/Audio Selection Button and LEDsSelecting an input Recalling a user presetInput Buttons, LEDs, and Label Window Front panel input label windowAuto imaging an input Picture Adjustment ButtonsBlack/Mute Button and LEDs LCD Display Adjustment KnobsPower Front Panel OperationsExtron Electronics ISM 60-425-01 Version Menu System OverviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuSync Type and Polarity submenu 000 Advanced Configuration MenuBlanking submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenuReset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenuSave Preset submenu User Presets menuExit menu Erase Preset submenuPicture Adjustments Flowchart Picture AdjustmentsFront Panel Security Lockout Flowchart Front Panel Security Lockout Executive ModeIP Information IP Information FlowchartOptimizing the Video Optimizing the Audio TroubleshootingSetting up a DVD source General Checks Specific ProblemsRS-232 Link Programming GuideEthernet Link Default Address= Hdtv SymbolsInput and Output Video Type Switcher-Initiated MessagesPower-up Ties Creation@BrtX1 Test Pattern RGB DelayPAL Film Mode Automated AdjustmentsUsing the Command and Response Table Host-to-Switcher InstructionsSwitcher Error Responses Command and Response Table for SIS Commands Horizontal size TintBrightness ContrastCommand and Response Table for SIS Commands Freeze User presetsDetail filter S-video and composite video inputs Auto MemoriesAudio mute Front panel security lockout Executive modeVerbose mode Set audio gain and attenuationInformation requests ResetsCommand and response table Command and Response Table for IP SIS CommandsSymbol definitions PAL film mode RGB delayScaler output settings Enhanced modeMemory backup Control Software for Windows Switcher SoftwareInstalling the Software Software Operation via Ethernet Ethernet protocol settingsIf you selected a comm port, proceed to step Using the Control ProgramWindows Control Program Window Button-Label Generator Using the Help ProgramExtron Button-Label Generator Window Using the SoftwareLoading the Startup Control Html OperationEnter Network Password Blacking out the Screen and Muting the Audio Changing the RGB DelayControl Creating a TieOutputting a Test Pattern Using Blue-Only ModeExecutive Mode Freezing the OutputAdministration Fields System ConfigurationHardware Address field ISM IP Settings FieldsISM IP Address field ISM Name fieldFile Management File ManagementO Configuration Input ConfigurationOutput Resolution, Rate, Sync Format, and Polarity Output format Output resolutionOutput rate Polarity Drop Box Output polarityOpening and Closing the Switcher Maintenance ModificationsRemoving the ISM Cover ISM Firmware Chip Locations Installing a Firmware UpgradeDVI Output Card Connector Opening and Socket J14 Installing a DVI Output CardOutput DVI Board Installation Cabling Ethernet ConnectionPinging to Determine the Web IP Address Determining Default AddressesPinging to Determine the Switcher IP Address Open Connecting as a Telnet ClientTelnet Tips Close Escape character and Esc keyLocal echo Set carriage return-line feedIncluded Parts Optional AccessoriesReference Information Part NumbersBulk cable Cables and ConnectorsAssorted connectors Button LabelsPage USA, Canada, South America Central America Japan Extron Warranty
Related manuals
Manual 105 pages 36.37 Kb