Extron electronic ISM 482 manual Software Operation via Ethernet, Ethernet protocol settings

Page 54

3.Scroll to the desired program and click Install (see figure 29).

Figure 29. Software Installation

4.Follow the on-screen instructions. By default, the installation of the installation routine creates a C:\Program Files\Extron\ISSISM directory, and it places the following five icons into a group folder named Extron Electronics\ISSISM:

•Button-Label Generator-

•Check for ISSISM Control Program Update

•ISSISM Control Program

•ISSISM Help

•Uninstall ISSISM Control Program

Software Operation via Ethernet

When an ISM is connected to an Ethernet WAN or LAN, any number of users can operate it, locally or remotely, using the ISS/ISM Control Program (see Ethernet connection on page 9 for installation details).

Connection to the switcher via the Ethernet is password protected. There are two levels of password protection: administrator and user. Administrators have full access to all ISM switching capabilities and editing functions. Users can select video and/or audio for output, select inputs and outputs, select test patterns, set RGB and audio mutes, select a blue screen, and view all settings with the exception of passwords. If the same passwords or no password is required for logging on, all personnel log on with administrator privileges. Fields and functions that exceed user privileges are grayed out in the ISS/ISM Control Program when the operator is logged on as a user.

Ethernet protocol settings

The IP Settings/Options screen (see figure 35 on page 51) provides a location for observing and, if you are connected via the RS-232 link or if logged on via the Ethernet port as an administrator, editing settings unique to the Ethernet interface. None of the fields on this screen can be edited while you are logged on as a user. See System Configuration Page on page 67, for details on the contents of these fields. See Ethernet Connection on page 69 for other basic information about Internet protocol.

NOTE: Editing variables on the IP Settings/Options screen while connected via the Ethernet port can immediately disconnect the user from the ISM. Extron recommends editing the settings on this screen using the RS-232 link and protecting the Ethernet access to this screen by assigning an administrator’s password to qualified and knowledgeable personnel only.

ISM 482 Integrated Scaling Matrix Switcher • Switcher Software

48

Page 53 Page 55
Image 54
Page 53 Page 55
Contents ISM No Photo Available yetSafety Instructions Specifications Availability Conventions Used in this Guide FCC Class a NoticeNotifications Software Commands  X! *X1@* X1%* X1** X1 CEContents Ethernet Connection Switcher SoftwareHtml Operation Reference InformationAbout the Switcher IntroductionAbout This Guide ISM Features InputsISM 482 Integrated Scaling Matrix Switcher Introduction Tabletop Placement InstallationMounting the Switcher Rack MountingCabling and Rear Panel Views Input ConnectionsConnections for Various Input Video Formats Standard Output Connections BNC Output Connections for Rgbhv and Rgbs VideoEthernet Connection Cabling and RJ-45 connector wiringOptional Output Connection Choosing a network cableRS-232 Connection ConfigurationWiring the network cable Pin RS-232 FunctionFront Panel Controls and Indicators OperationVideo/Audio Selection Button and LEDs Output Buttons and LEDsFront panel input label window Recalling a user presetInput Buttons, LEDs, and Label Window Selecting an inputPicture Adjustment Buttons Black/Mute Button and LEDsAuto imaging an input Front Panel Operations Adjustment KnobsPower LCD DisplayMenu System Overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuSync Type and Polarity submenu Advanced Configuration Menu 000Test Pattern submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Blanking submenuPAL Film Mode submenu Enhanced Mode submenuPixel Phase submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture Adjustments Picture Adjustments FlowchartFront Panel Security Lockout Executive Mode Front Panel Security Lockout FlowchartIP Information Flowchart IP InformationOptimizing the Video Troubleshooting Setting up a DVD sourceOptimizing the Audio Specific Problems General ChecksProgramming Guide RS-232 LinkDefault Address Ethernet LinkSymbols = HdtvTies Creation Switcher-Initiated MessagesPower-up Input and Output Video Type@BrtX1 Automated Adjustments RGB DelayPAL Film Mode Test PatternHost-to-Switcher Instructions Switcher Error ResponsesUsing the Command and Response Table Command and Response Table for SIS Commands Contrast TintBrightness Horizontal sizeCommand and Response Table for SIS Commands Auto Memories User presetsDetail filter S-video and composite video inputs FreezeSet audio gain and attenuation Front panel security lockout Executive modeVerbose mode Audio muteResets Information requestsCommand and Response Table for IP SIS Commands Symbol definitionsCommand and response table Enhanced mode RGB delayScaler output settings PAL film modeMemory backup Switcher Software Installing the SoftwareControl Software for Windows Ethernet protocol settings Software Operation via EthernetUsing the Control Program If you selected a comm port, proceed to stepWindows Control Program Window Using the Help Program Button-Label GeneratorUsing the Software Extron Button-Label Generator WindowHtml Operation Loading the Startup ControlEnter Network Password Creating a Tie Changing the RGB DelayControl Blacking out the Screen and Muting the AudioFreezing the Output Using Blue-Only ModeExecutive Mode Outputting a Test PatternSystem Configuration Administration FieldsISM Name field ISM IP Settings FieldsISM IP Address field Hardware Address fieldFile Management File ManagementInput Configuration O ConfigurationOutput Resolution, Rate, Sync Format, and Polarity Output resolution Output rateOutput format Output polarity Polarity Drop BoxMaintenance Modifications Opening and Closing the SwitcherRemoving the ISM Cover Installing a Firmware Upgrade ISM Firmware Chip LocationsInstalling a DVI Output Card DVI Output Card Connector Opening and Socket J14Output DVI Board Installation Ethernet Connection CablingDetermining Default Addresses Pinging to Determine the Switcher IP AddressPinging to Determine the Web IP Address Connecting as a Telnet Client Telnet TipsOpen Set carriage return-line feed Escape character and Esc keyLocal echo ClosePart Numbers Optional AccessoriesReference Information Included PartsButton Labels Cables and ConnectorsAssorted connectors Bulk cablePage Extron Warranty USA, Canada, South America Central America Japan
Related manuals
Manual 105 pages 36.37 Kb
Top Page Image Contents