Extron electronic ISM 482 manual Picture Adjustments Flowchart

Page 31

Picture Adjustments

The picture adjustments allow you to fine tune the image quality of the selected input. When you press one of the Picture Adjustments buttons (Color/Tint, Brightness/Contrast, Size, Center, or Filter) once, the corresponding image adjustment menu for the selected output (lit Output LED) image appears on the LCD screen. Select the other output using the Output buttons to call the image adjustment menu for the other output. In either screen, adjustments can then be made by rotating the Adjust knob or the Adjust knob. Picture adjustment settings are stored in nonvolatile memory; when the switcher is powered down and powered up, the settings are restored.

Adjust an image for centering, sizing, brightness, contrast, color, tint, zoom, or detail as follows (see figure 23):

	Extron Electronics		Extron Electronics
	ISM 482		ISM 482
Power	Integration		60-425-01		Display
on	Scaling Matrix	2 sec.	Version xxxx	2 sec.	Cycle

COLOR/

BRT/

SIZE

CENTER

FILTER

TINT

CONT

Output #1

Output #1

Output #1

Output #1

Output #1

Color

Tint

Brightness

Contrast

Horz

Size

Vert

Horz

Center Vert

Horz

Filter Vert

127

128

063

063

450

400

500

550

3

7

NOTE: Press the appropriate output button to select the desired output.

10 sec. timeout

NOTE: The Adjust knob and the Adjust knob are used to adjust the image settings on the left and right sides of the LCD screen, respectively.

Figure 23. Picture Adjustments Flowchart

1.Press the desired input button and output button to select an input-output tie to adjust.

NOTES:

•The adjustments are made to the input signal as it is switched to the tied output (1 or 2) only. (The output LED is lit and the selected output is shown in the LCD). The adjustments do not affect the same input tied to the other output.

•Color adjustments are available only for component video, S-video, and composite video inputs.

Tint adjustments are available only for S-video and composite video inputs.

2.Press the appropriate picture adjustment button: color and tint, brightness and contrast (Brt/Cont), sizing (Size), centering (Center), or filter. The LCD display shows the name of the adjustment and the current setting value.

ISM 482 Integrated Scaling Matrix Switcher • Operation

25

Image 31

Contents No Photo Available yet ISMSafety Instructions FCC Class a Notice Specifications Availability Conventions Used in this GuideNotifications X! *X1@* X1%* X1** X1 CE Software CommandsContents Reference Information Switcher SoftwareHtml Operation Ethernet ConnectionIntroduction About the SwitcherAbout This Guide ISM Inputs FeaturesISM 482 Integrated Scaling Matrix Switcher Introduction Rack Mounting InstallationMounting the Switcher Tabletop PlacementInput Connections Cabling and Rear Panel ViewsConnections for Various Input Video Formats BNC Output Connections for Rgbhv and Rgbs Video Standard Output ConnectionsChoosing a network cable Cabling and RJ-45 connector wiringOptional Output Connection Ethernet ConnectionPin RS-232 Function ConfigurationWiring the network cable RS-232 ConnectionOperation Front Panel Controls and IndicatorsOutput Buttons and LEDs Video/Audio Selection Button and LEDsSelecting an input Recalling a user presetInput Buttons, LEDs, and Label Window Front panel input label windowBlack/Mute Button and LEDs Picture Adjustment ButtonsAuto imaging an input LCD Display Adjustment KnobsPower Front Panel OperationsExtron Electronics ISM 60-425-01 Version Menu System OverviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuSync Type and Polarity submenu 000 Advanced Configuration MenuBlanking submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenuReset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenuSave Preset submenu User Presets menuExit menu Erase Preset submenuPicture Adjustments Flowchart Picture AdjustmentsFront Panel Security Lockout Flowchart Front Panel Security Lockout Executive ModeIP Information IP Information FlowchartOptimizing the Video Setting up a DVD source TroubleshootingOptimizing the Audio General Checks Specific ProblemsRS-232 Link Programming GuideEthernet Link Default Address= Hdtv SymbolsInput and Output Video Type Switcher-Initiated MessagesPower-up Ties Creation@BrtX1 Test Pattern RGB DelayPAL Film Mode Automated AdjustmentsSwitcher Error Responses Host-to-Switcher InstructionsUsing the Command and Response Table Command and Response Table for SIS Commands Horizontal size TintBrightness ContrastCommand and Response Table for SIS Commands Freeze User presetsDetail filter S-video and composite video inputs Auto MemoriesAudio mute Front panel security lockout Executive modeVerbose mode Set audio gain and attenuationInformation requests ResetsSymbol definitions Command and Response Table for IP SIS CommandsCommand and response table PAL film mode RGB delayScaler output settings Enhanced modeMemory backup Installing the Software Switcher SoftwareControl Software for Windows Software Operation via Ethernet Ethernet protocol settingsIf you selected a comm port, proceed to step Using the Control ProgramWindows Control Program Window Button-Label Generator Using the Help ProgramExtron Button-Label Generator Window Using the SoftwareLoading the Startup Control Html OperationEnter Network Password Blacking out the Screen and Muting the Audio Changing the RGB DelayControl Creating a TieOutputting a Test Pattern Using Blue-Only ModeExecutive Mode Freezing the OutputAdministration Fields System ConfigurationHardware Address field ISM IP Settings FieldsISM IP Address field ISM Name fieldFile Management File ManagementO Configuration Input ConfigurationOutput Resolution, Rate, Sync Format, and Polarity Output rate Output resolutionOutput format Polarity Drop Box Output polarityOpening and Closing the Switcher Maintenance ModificationsRemoving the ISM Cover ISM Firmware Chip Locations Installing a Firmware UpgradeDVI Output Card Connector Opening and Socket J14 Installing a DVI Output CardOutput DVI Board Installation Cabling Ethernet ConnectionPinging to Determine the Switcher IP Address Determining Default AddressesPinging to Determine the Web IP Address Telnet Tips Connecting as a Telnet ClientOpen Close Escape character and Esc keyLocal echo Set carriage return-line feedIncluded Parts Optional AccessoriesReference Information Part NumbersBulk cable Cables and ConnectorsAssorted connectors Button LabelsPage USA, Canada, South America Central America Japan Extron Warranty

Related manuals

Manual 105 pages 36.37 Kb