Extron electronic ISM 482 manual Output DVI Board Installation

Page 74

4.Position the DVI card above connector J14 with the DVI connector facing toward the rear of the switcher. Ensure that the pins on the DVI card properly align with the J14 connector to prevent bending the pins.

5.Carefully mate the 45-pin connector on the DVI output board with connector J14 on the main circuit board (see figure 52).

DVI Connector on

DVI Output Card

DVI Output Card

DVI Output Card

Mated to the

Main Board via

Connector J14

Figure 52. Output DVI Board Installation

6.Secure the DVI card to the rear panel with the two screws removed in step 3.

7.Close the switcher (see “Opening and Closing the Switcher,” starting with step 9 on on page 65).

ISM 482 Integrated Scaling Matrix Switcher • Maintenance and Modifications

68

Image 74

Contents ISM No Photo Available yetSafety Instructions Notifications Specifications Availability Conventions Used in this GuideFCC Class a Notice Software Commands X! *X1@* X1%* X1** X1 CEContents Ethernet Connection Switcher SoftwareHtml Operation Reference InformationAbout This Guide About the SwitcherIntroduction ISM Features InputsISM 482 Integrated Scaling Matrix Switcher Introduction Tabletop Placement InstallationMounting the Switcher Rack MountingCabling and Rear Panel Views Input ConnectionsConnections for Various Input Video Formats Standard Output Connections BNC Output Connections for Rgbhv and Rgbs VideoEthernet Connection Cabling and RJ-45 connector wiringOptional Output Connection Choosing a network cableRS-232 Connection ConfigurationWiring the network cable Pin RS-232 FunctionFront Panel Controls and Indicators OperationVideo/Audio Selection Button and LEDs Output Buttons and LEDsFront panel input label window Recalling a user presetInput Buttons, LEDs, and Label Window Selecting an inputAuto imaging an input Picture Adjustment ButtonsBlack/Mute Button and LEDs Front Panel Operations Adjustment KnobsPower LCD DisplayMenu System Overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuSync Type and Polarity submenu Advanced Configuration Menu 000Test Pattern submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Blanking submenuPAL Film Mode submenu Enhanced Mode submenuPixel Phase submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture Adjustments Picture Adjustments FlowchartFront Panel Security Lockout Executive Mode Front Panel Security Lockout FlowchartIP Information Flowchart IP InformationOptimizing the Video Optimizing the Audio TroubleshootingSetting up a DVD source Specific Problems General ChecksProgramming Guide RS-232 LinkDefault Address Ethernet LinkSymbols = HdtvTies Creation Switcher-Initiated MessagesPower-up Input and Output Video Type@BrtX1 Automated Adjustments RGB DelayPAL Film Mode Test PatternUsing the Command and Response Table Host-to-Switcher InstructionsSwitcher Error Responses Command and Response Table for SIS Commands Contrast TintBrightness Horizontal sizeCommand and Response Table for SIS Commands Auto Memories User presetsDetail filter S-video and composite video inputs FreezeSet audio gain and attenuation Front panel security lockout Executive modeVerbose mode Audio muteResets Information requestsCommand and response table Command and Response Table for IP SIS CommandsSymbol definitions Enhanced mode RGB delayScaler output settings PAL film modeMemory backup Control Software for Windows Switcher SoftwareInstalling the Software Ethernet protocol settings Software Operation via EthernetUsing the Control Program If you selected a comm port, proceed to stepWindows Control Program Window Using the Help Program Button-Label GeneratorUsing the Software Extron Button-Label Generator WindowHtml Operation Loading the Startup ControlEnter Network Password Creating a Tie Changing the RGB DelayControl Blacking out the Screen and Muting the AudioFreezing the Output Using Blue-Only ModeExecutive Mode Outputting a Test PatternSystem Configuration Administration FieldsISM Name field ISM IP Settings FieldsISM IP Address field Hardware Address fieldFile Management File ManagementInput Configuration O ConfigurationOutput Resolution, Rate, Sync Format, and Polarity Output format Output resolutionOutput rate Output polarity Polarity Drop BoxMaintenance Modifications Opening and Closing the SwitcherRemoving the ISM Cover Installing a Firmware Upgrade ISM Firmware Chip LocationsInstalling a DVI Output Card DVI Output Card Connector Opening and Socket J14Output DVI Board Installation Ethernet Connection CablingPinging to Determine the Web IP Address Determining Default AddressesPinging to Determine the Switcher IP Address Open Connecting as a Telnet ClientTelnet Tips Set carriage return-line feed Escape character and Esc keyLocal echo ClosePart Numbers Optional AccessoriesReference Information Included PartsButton Labels Cables and ConnectorsAssorted connectors Bulk cablePage Extron Warranty USA, Canada, South America Central America Japan

Related manuals

Manual 105 pages 36.37 Kb