Extron electronic ISM 482 manual IP Information Flowchart

Page 33

IP Information

To set up the ISM for operation via its Ethernet port, you need to know and be able to change the IP address. One way to do this is via the IP address and hardware address screen.

To access the IP address and hardware address screen, press and hold the Color/Tint and Detail buttons while you apply power to the ISM (see figure 25). When the ISM is finished initializing, it displays both addresses.

Press and hold both buttons

simultaneously while applying power.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COLOR/

 

DETAIL

 

 

TINT

 

 

 

 

IP Address

Power

>192.168.254.254

 

Hardware Address 00-80-00-00-04-04

Select the IP address subfield

Change the subfield value

with the Adjust knob.

with the Adjust knob.

IP Address 192.168.255>253 Hardware Address 00-80-00-00-04-04

10 sec.

Default

Cycle

NOTE: The hardware address is hardcoded and cannot be changed.

Figure 25. IP Information Flowchart

If you need to change the IP address, use the Adjust knob to select the desired subfield. Rotate the Adjust knob to change the value. Repeat the adjustment for other subfields as required.

Valid IP addresses consist of four 1-, 2-, or 3-digit numeric subfields separated by dots (periods). Each field can be numbered from 000 through 255. Leading zeroes, up to 3 digits total per field, are optional. Values of 256 and above are invalid.

NOTES:

If the local system administrators have not changed the value, the factory- specified default, 192.168.254.254, is the correct value for this field.

The hardware address is hardcoded and cannot be changed.

ISM 482 Integrated Scaling Matrix Switcher • Operation

27

Image 33
Contents No Photo Available yet ISMSafety Instructions Specifications Availability Conventions Used in this Guide FCC Class a NoticeNotifications  X! *X1@* X1%* X1** X1 CE Software CommandsContents Html Operation Switcher SoftwareEthernet Connection Reference InformationAbout the Switcher IntroductionAbout This Guide ISM Inputs FeaturesISM 482 Integrated Scaling Matrix Switcher Introduction Mounting the Switcher InstallationTabletop Placement Rack MountingInput Connections Cabling and Rear Panel ViewsConnections for Various Input Video Formats BNC Output Connections for Rgbhv and Rgbs Video Standard Output ConnectionsOptional Output Connection Cabling and RJ-45 connector wiringEthernet Connection Choosing a network cableWiring the network cable ConfigurationRS-232 Connection Pin RS-232 FunctionOperation Front Panel Controls and IndicatorsOutput Buttons and LEDs Video/Audio Selection Button and LEDsInput Buttons, LEDs, and Label Window Recalling a user presetFront panel input label window Selecting an inputPicture Adjustment Buttons Black/Mute Button and LEDsAuto imaging an input Power Adjustment KnobsFront Panel Operations LCD DisplayExtron Electronics ISM 60-425-01 Version Menu System OverviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuSync Type and Polarity submenu 000 Advanced Configuration MenuRGB Delay submenu Blue-Only Mode and Edge Smoothing submenuTest Pattern submenu Blanking submenuPixel Phase submenu Enhanced Mode submenuPAL Film Mode submenu Reset submenuSave Preset submenu User Presets menuExit menu Erase Preset submenuPicture Adjustments Flowchart Picture AdjustmentsFront Panel Security Lockout Flowchart Front Panel Security Lockout Executive ModeIP Information IP Information FlowchartOptimizing the Video Troubleshooting Setting up a DVD sourceOptimizing the Audio General Checks Specific ProblemsRS-232 Link Programming GuideEthernet Link Default Address= Hdtv SymbolsPower-up Switcher-Initiated MessagesTies Creation Input and Output Video Type@BrtX1 PAL Film Mode RGB DelayAutomated Adjustments Test PatternHost-to-Switcher Instructions Switcher Error ResponsesUsing the Command and Response Table Command and Response Table for SIS Commands Brightness TintContrast Horizontal sizeCommand and Response Table for SIS Commands Detail filter S-video and composite video inputs User presetsAuto Memories FreezeVerbose mode Front panel security lockout Executive modeSet audio gain and attenuation Audio muteInformation requests ResetsCommand and Response Table for IP SIS Commands Symbol definitionsCommand and response table Scaler output settings RGB delayEnhanced mode PAL film modeMemory backup Switcher Software Installing the SoftwareControl Software for Windows Software Operation via Ethernet Ethernet protocol settingsIf you selected a comm port, proceed to step Using the Control ProgramWindows Control Program Window Button-Label Generator Using the Help ProgramExtron Button-Label Generator Window Using the SoftwareLoading the Startup Control Html OperationEnter Network Password Control Changing the RGB DelayCreating a Tie Blacking out the Screen and Muting the AudioExecutive Mode Using Blue-Only ModeFreezing the Output Outputting a Test PatternAdministration Fields System ConfigurationISM IP Address field ISM IP Settings FieldsISM Name field Hardware Address fieldFile Management File ManagementO Configuration Input ConfigurationOutput Resolution, Rate, Sync Format, and Polarity Output resolution Output rateOutput format Polarity Drop Box Output polarityOpening and Closing the Switcher Maintenance ModificationsRemoving the ISM Cover ISM Firmware Chip Locations Installing a Firmware UpgradeDVI Output Card Connector Opening and Socket J14 Installing a DVI Output CardOutput DVI Board Installation Cabling Ethernet ConnectionDetermining Default Addresses Pinging to Determine the Switcher IP AddressPinging to Determine the Web IP Address Connecting as a Telnet Client Telnet TipsOpen Local echo Escape character and Esc keySet carriage return-line feed CloseReference Information Optional AccessoriesPart Numbers Included PartsAssorted connectors Cables and ConnectorsButton Labels Bulk cablePage USA, Canada, South America Central America Japan Extron Warranty
Related manuals
Manual 105 pages 36.37 Kb