Extron electronic ISM 482 manual Removing the ISM Cover

Page 71

3

4Remove top two front panel screws.

Disconnect from/

6connect to J8 and J13.

5

Remove (16) screws.

Lift cover straight up.

J8J13

Extron ISM 482

Switcher

 

 

 

8

 

 

 

7

 

 

 

R

 

 

6

R

 

 

 

INPU

TS 5

R

 

 

G

4

R

 

 

 

 

G

 

3

R

 

 

 

 

G

 

 

2

 

B

 

R

 

G

 

1

 

 

B

R

 

 

 

G

 

 

 

 

B

/HV

R

 

 

G

 

 

H

 

 

B

V

 

 

 

 

H/H

 

G

B

 

 

 

 

 

H/HV

 

G

B

 

V

 

 

 

 

H/H

 

 

B

H/H

V

 

B

 

 

8

 

H/HV

 

 

 

 

 

7

 

 

V

 

6

 

 

H/H

 

 

H/H

V

5

 

 

4 3

2

1

B

H/HV

V

V

H/H

V

 

Figure 49. Removing the ISM Cover

4.Remove the top two front panel screws.

5.Lift the top cover straight up approximately 5 inches until you can access the fan power cords.

ATTENTION: Do not touch any switches or other electronic components inside the ISM. Doing so could damage the switcher. Electrostatic discharge (ESD) can damage IC chips even though you cannot feel it. You must be electrically grounded before proceeding with firmware replacement. A grounding wrist strap is recommended.

6.Disconnect the two fan power cords from connectors J8 and J13 on the main board.

7.Lift the top cover out of the way.

8.Perform the desired maintenance procedure (see “Installing a Firmware Upgrade” on the next page or Installing a DVI Output Card on page 67).

9.Reconnect the two fan power cords to connectors J8 and J13 on the main board. It does not matter which fan is connected to which connector.

ISM 482 Integrated Scaling Matrix Switcher • Maintenance and Modifications

65

Page 70 Page 72
Image 71
Page 70 Page 72
Contents No Photo Available yet ISMSafety Instructions Notifications Specifications Availability Conventions Used in this GuideFCC Class a Notice  X! *X1@* X1%* X1** X1 CE Software CommandsContents Reference Information Switcher SoftwareHtml Operation Ethernet ConnectionAbout This Guide About the SwitcherIntroduction ISM Inputs FeaturesISM 482 Integrated Scaling Matrix Switcher Introduction Rack Mounting InstallationMounting the Switcher Tabletop PlacementInput Connections Cabling and Rear Panel ViewsConnections for Various Input Video Formats BNC Output Connections for Rgbhv and Rgbs Video Standard Output ConnectionsChoosing a network cable Cabling and RJ-45 connector wiringOptional Output Connection Ethernet ConnectionPin RS-232 Function ConfigurationWiring the network cable RS-232 ConnectionOperation Front Panel Controls and IndicatorsOutput Buttons and LEDs Video/Audio Selection Button and LEDsSelecting an input Recalling a user presetInput Buttons, LEDs, and Label Window Front panel input label windowAuto imaging an input Picture Adjustment ButtonsBlack/Mute Button and LEDs LCD Display Adjustment KnobsPower Front Panel OperationsExtron Electronics ISM 60-425-01 Version Menu System OverviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuSync Type and Polarity submenu 000 Advanced Configuration MenuBlanking submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenuReset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenuSave Preset submenu User Presets menuExit menu Erase Preset submenuPicture Adjustments Flowchart Picture AdjustmentsFront Panel Security Lockout Flowchart Front Panel Security Lockout Executive ModeIP Information IP Information FlowchartOptimizing the Video Optimizing the Audio TroubleshootingSetting up a DVD source General Checks Specific ProblemsRS-232 Link Programming GuideEthernet Link Default Address= Hdtv SymbolsInput and Output Video Type Switcher-Initiated MessagesPower-up Ties Creation@BrtX1 Test Pattern RGB DelayPAL Film Mode Automated AdjustmentsUsing the Command and Response Table Host-to-Switcher InstructionsSwitcher Error Responses Command and Response Table for SIS Commands Horizontal size TintBrightness ContrastCommand and Response Table for SIS Commands Freeze User presetsDetail filter S-video and composite video inputs Auto MemoriesAudio mute Front panel security lockout Executive modeVerbose mode Set audio gain and attenuationInformation requests ResetsCommand and response table Command and Response Table for IP SIS CommandsSymbol definitions PAL film mode RGB delayScaler output settings Enhanced modeMemory backup Control Software for Windows Switcher SoftwareInstalling the Software Software Operation via Ethernet Ethernet protocol settingsIf you selected a comm port, proceed to step Using the Control ProgramWindows Control Program Window Button-Label Generator Using the Help ProgramExtron Button-Label Generator Window Using the SoftwareLoading the Startup Control Html OperationEnter Network Password Blacking out the Screen and Muting the Audio Changing the RGB DelayControl Creating a TieOutputting a Test Pattern Using Blue-Only ModeExecutive Mode Freezing the OutputAdministration Fields System ConfigurationHardware Address field ISM IP Settings FieldsISM IP Address field ISM Name fieldFile Management File ManagementO Configuration Input ConfigurationOutput Resolution, Rate, Sync Format, and Polarity Output format Output resolutionOutput rate Polarity Drop Box Output polarityOpening and Closing the Switcher Maintenance ModificationsRemoving the ISM Cover ISM Firmware Chip Locations Installing a Firmware UpgradeDVI Output Card Connector Opening and Socket J14 Installing a DVI Output CardOutput DVI Board Installation Cabling Ethernet ConnectionPinging to Determine the Web IP Address Determining Default AddressesPinging to Determine the Switcher IP Address Open Connecting as a Telnet ClientTelnet Tips Close Escape character and Esc keyLocal echo Set carriage return-line feedIncluded Parts Optional AccessoriesReference Information Part NumbersBulk cable Cables and ConnectorsAssorted connectors Button LabelsPage USA, Canada, South America Central America Japan Extron Warranty
Related manuals
Manual 105 pages 36.37 Kb
Top Page Image Contents