ATTO Technology 5300 Measure drive performance, Click the Set up Error Notification button

Page 20

message; it cannot respond to a rejection by a server for an invalid address. Ensure all E-mail addresses typed in are valid.

Each E-mail is time stamped when it leaves as part of the SMTP header information as shown in Exhibit 3.0-1.

1If you are not already in the FastStream GUI, type the IP address of your appliance, as found

in Use the FastStream VT 5300 GUI on page

23, in a standard browser, click Enter Here and type in your username and password.

2The Monitor VTL page appears. On the menu at the left hand side of the page, choose Manage.

3The Manage VTL page appears. Click on the FastStream arrow.

4Click the Set up Error Notification button

5Click Next.

6Click on the Enabled button for Notification

Configuration

7Type in the sender address (E-mails show this name in the From field)

8Type in the SMTP Server IP Address

9Type in the Username and Password of your SMTP E-mail account

10Type in up to five E-mail addresses

11Choose All, Critical or Warning for each E- mail address.

12When all information is typed in, click Commit.

13Your settings are displayed. You may change or disable E-mail notification at any time from the Error Notification page.

Exhibit 3.0-1 The E-mail messages sent by the FastStream VT 5300 follow this format.

Subject: [The Type of Event that Occurred]

Message Body:

This is a status message from [FastStream name]. Identifying information as well as the most recent entries from the event log appear below.

***************

Unit Information

***************

Serial Number :

[Serial Number]

 

IP Addresses:

[IP Address1]

 

***************

[IP Address2]

****************

Event Log Entries

[Listing of the

ten latest event log entries]

Measure drive performance

CAUTION

New performance data is updated every 60 seconds which impacts performance slightly, even if you minimize the browser window. Exit the browser GUI completely whenever you need maximum performance.

The FastStream VT 5300 collects various metrics to measure performance for physical drives attached to the FastStream during normal system operation and drive initialization and verification.

1If you are not already in the FastStream GUI, type the IP address of your appliance, as found

in Use the FastStream VT 5300 GUI on page

23, in a standard browser, click Enter Here and type in your username and password.

2The Monitor VTL page appears. On the menu at the left hand side of the page, click on Diagnostics.

3The Diagnostics Menu page appears. Select Drive Performance and Health.

4Click Next.

5The Drive Performance and Health page appears. Click on a drive in the drive section.

6Click Start.

7Drive performance is displayed under the Drive Metrics section of the page.

15

ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual

Page 19 Page 21
Image 20
Page 19 Page 21
Contents FastStream VT Page Page Contents Update storage and firmware Appendix E Warranty, contact information XxiModify storage Interface optionsHardware features Virtual Tape featuresBackup and restore features Management and control featuresGbE network Gb FC Switch GbE SwitchEthernet Fibre Channel Physical attributes Installation Installation Unpack the packing box verify contentsInstall the FastStream Install Windows driversBegin initial configuration Click on Launch BrowserConfigure Virtual Tape Use quick initial configuration Use custom initial setupUse Hot Spare devices Click on the Add/Remove Hot Spares buttonClick in the Enable/Disable Write Protection button Enable/Disable Write Protection page appearsSecure data through Write Protection Move Virtual Tape CartridgesOptional changes to system parameters Customize the username, passwordChange system configurations Changes to other parameters may be made using the Advanced Advanced CLIMonitor storage and diagnose configurations Monitor VTLPhone home E-mail messages Configuration DisplayHealth and Status Monitor Measure drive performance Click the Set up Error Notification buttonConfiguration Scan drive surfaces Verify storageClick the Initialize and Verify button Select Verify OnlyAdd drives to a RAID Group Modify storageInitialize and verify drives Rebuild RAID Groups Add or remove Hot SparesSelect Rebuild RAID Groups Select the Add/Remove Hot Spares buttonClick in the Delete Virtual Tape Library button Add a VTL from another FastStream VTLDelete a VTL Move Virtual Tape Cartridges Update storage and firmware Remove stale VTL configuration dataUpdate firmware Preliminary stepsUse FTP over Ethernet Use the RS-232 serial linkSend File Click Send FileType FastStream VT 5300 in the New Connection dialog box Interface optionsUse the serial port Use Telnet EnterCable types Appendix a CablingScsi cabling Fibre Channel connections Cable lengthAppendix B Designing RAID groups Jbod Just a Bunch of DisksRAID Level DiskIv Appendix Symbol Indicates Appendix C CLI provides an ASCII-based interfaceCLI error messages Mp1Command Default Example CLI summaryViii Appendix Sntp CLI command explanations DefaultInterleave DHCPFixedDelayDriveTestConfig DumpConfigEmailPassword EmailNotifyAddressEmailServerAddress EmailUsernameFCPortErrors FCDataRateFCHard FCHardAddressPassword IPGatewayIPSubnetMask IsReservedRAIDCommandTimeout ResetFCPortErrorsRestoreConfiguration RGCancelAddStorageRGWaitTimeout RGDisplayRGHaltConversion RGHaltRebuildSaveConfiguration SCSIPortResetSCSIPortResetOnStartup RMStatusSerialPortBaudRate SerialPortEchoSNTPServer TailEventLogThis equipment generates, uses, and can radiate radio Further results of FCC TestingAppendix D Standards and compliances European Standards Declaration of ConformityContact Atto Technology, Inc Appendix E Warranty, contact informationManufacturer limited warranty Xxii Appendix
Top Page Image Contents