ATTO Technology 5300 DefaultInterleave, DHCPFixedDelay, DisplayEventLogFilter, DriveTest

Page 40

DefaultInterleave

DefaultInterleave assigns or retrieves the system-default interleave size for new RAID Groups. If an interleave size is not explicitly specified when a RAID Group is created, then the DefaultInterleave value is used instead.

Default: 128

set DefaultInterleave [16 32 64 128 256 ] get DefaultInterleave

DHCPFixedDelay

Selects/displays the delay, in seconds, between DHCP client request intervals, from between 0 seconds to 255 seconds. 0 time is typical.

Default: 0 (no delay)

set DHCPFixedDelay [ 0 - 255 ] get DHCPFixedDelay

DisplayEventLog

Displays the most recent page of event log entries. Typing a +, - or = causes the next, previous or same page of event log entries to be displayed. No events are recorded until the command has been completed. Type q to disable the command, begin new log entries, and return to CLI.

DisplayEventLog < + - = q >

DisplayEventLogFilter

Filters the display of data for specified subsystems and levels during DisplayEventLog mode. Valid event log subsystem entries are platform-dependent.

Subsystem

Levels

ECC

INFO

ENET

WARN

GEN

CRIT

HTTP

FAIL

NVRAM

ALL

PERF

 

SCSI

 

NDMP

 

FC

 

ALL Default: all all

set DisplayEventLogFilter [subsystem all] [level all] get DisplayEventLogFilter [subsystem all] [level all]

DriveTest

Immediate command which starts or stops a drive test with the previously specified configuration and drive list. Drives which are in-use by the test are not available for RAID configuration or RAID operations. Only one test can be run at a time.

DriveTest [Begin Cancel]

xi

DriveTestConfig

Configures the next drive test to perform one of the following operations: initialize (destructive write-only), read (non-destructive read-only), verify (destructive verify), or init-verify (destructive write-read-verify).The test is not started until the DriveTest Begin command is given.

Default: not initiated

set DriveTestConfig [init read verify init-verify] get DriveTestConfig

DriveTestList

Specifies drives to be run in the next drive test including drives which are not part of a RAID group and not Hot Spares. The all parameter automatically chooses eligible drives. The test is not started until the DriveTest Begin command is given.

set DriveTestList [drive [BlockDevID] all] get DriveTestList

DriveTestStatus

Displays the status of the currently running drive test but does not display performance metrics. If a block device ID is not running or cannot be found, its state is idle and percent complete is 0.

get DriveTestStatus <drive [BlockDevID]>

DumpConfig

Displays a unit’s configuration.

DumpConfig

DumpEventLog

Dumps the contents of the entire event log to the current CLI session without impact on the log itself (the log is not cleared). No events are recorded until the command has been completed.

DumpEventLog

EmailFromAddress

Configures the E-mail address that the FastStream uses to talk to the E-mail server. Full E-mail address is a fully qualified Internet E-mail address, not more than 128 characters.

set EmailFromAddress [full email address] get EmailFromAddress

EmailNotify

Regulates E-mail notification.

Default: disabled.

set EmailNotify [enabled disabled] Requires a SaveConfiguration command get EmailNotify

ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual

Page 39 Page 41
Image 40
Page 39 Page 41
Contents FastStream VT Page Page Contents Update storage and firmware Appendix E Warranty, contact information XxiModify storage Interface optionsHardware features Virtual Tape featuresBackup and restore features Management and control featuresEthernet Fibre Channel Gb FC Switch GbE SwitchGbE network Physical attributes Installation Installation Unpack the packing box verify contentsInstall the FastStream Install Windows driversBegin initial configuration Click on Launch BrowserConfigure Virtual Tape Use quick initial configuration Use custom initial setupUse Hot Spare devices Click on the Add/Remove Hot Spares buttonClick in the Enable/Disable Write Protection button Enable/Disable Write Protection page appearsSecure data through Write Protection Move Virtual Tape CartridgesChange system configurations Customize the username, passwordOptional changes to system parameters Changes to other parameters may be made using the Advanced Advanced CLIMonitor storage and diagnose configurations Monitor VTLHealth and Status Monitor Configuration DisplayPhone home E-mail messages Configuration Click the Set up Error Notification buttonMeasure drive performance Scan drive surfaces Verify storageClick the Initialize and Verify button Select Verify OnlyInitialize and verify drives Modify storageAdd drives to a RAID Group Rebuild RAID Groups Add or remove Hot SparesSelect Rebuild RAID Groups Select the Add/Remove Hot Spares buttonDelete a VTL Add a VTL from another FastStream VTLClick in the Delete Virtual Tape Library button Move Virtual Tape Cartridges Update storage and firmware Remove stale VTL configuration dataUpdate firmware Preliminary stepsUse FTP over Ethernet Use the RS-232 serial linkSend File Click Send FileUse the serial port Interface optionsType FastStream VT 5300 in the New Connection dialog box Use Telnet EnterScsi cabling Appendix a CablingCable types Fibre Channel connections Cable lengthAppendix B Designing RAID groups Jbod Just a Bunch of DisksRAID Level DiskIv Appendix Symbol Indicates Appendix C CLI provides an ASCII-based interfaceCLI error messages Mp1Command Default Example CLI summaryViii Appendix Sntp CLI command explanations DefaultInterleave DHCPFixedDelayDriveTestConfig DumpConfigEmailPassword EmailNotifyAddressEmailServerAddress EmailUsernameFCPortErrors FCDataRateFCHard FCHardAddressPassword IPGatewayIPSubnetMask IsReservedRAIDCommandTimeout ResetFCPortErrorsRestoreConfiguration RGCancelAddStorageRGWaitTimeout RGDisplayRGHaltConversion RGHaltRebuildSaveConfiguration SCSIPortResetSCSIPortResetOnStartup RMStatusSerialPortBaudRate SerialPortEchoSNTPServer TailEventLogAppendix D Standards and compliances Further results of FCC TestingThis equipment generates, uses, and can radiate radio European Standards Declaration of ConformityManufacturer limited warranty Appendix E Warranty, contact informationContact Atto Technology, Inc Xxii Appendix
Top Page Image Contents