ATTO Technology FastStream VT SerialPortBaudRate, SerialPortEcho, SNTPServer, TailEventLog, Time

Page 47

SerialPortBaudRate

Configures the baud rate for the unit’s RS-232 serial port. The number of data bits is fixed at 8 with no parity.

set SerialPortBaudRate [ 2400 9600 19200 38400 57600 115200]

get SerialPortBaudRate

SerialPortEcho

Controls if the unit echoes characters on its RS-232 port. When enabled, all non-control character keyboard input is output to the display.

Default: enabled

set SerialPortEcho [enabled disabled] get SerialPortEcho

SNTP

Controls whether SNTP time server is used.

Default: enabled

set SNTP [enabled disabled] get SNTP

SNTPServer

Controls or displays the main IP address the client uses to retrieve the SNTP time.

Default: 192.43.244.18

set SNTPServer[xxx.xxx.xxx.xxx] get SNTPServer

TailEventLog

Displays new events to the terminal. Type q and press Enter to exit tail mode.

TailEventLog

TapeLibDelete

Deletes the specified tape library or all tape libraries.

TapeLibDelete [GroupName all]

TapeLibInfo

Lists information for the specified tape library or all tape libraries.

TapeLibInfo [LibName all]

TapeWriteProtect

Enables or disables write protection for a particular virtual tape or both virtual tapes.

set TapeWriteProtect [TapeVol ID all] [enabled disabled]

get TapeWriteProtect

Time

Controls or displays the current time as clocked by the unit in 24 hour format. Time cannot be set while SNTP is enabled.

set Time [HH: MM: SS] get Time

TimeZone

Controls or displays the time zone or an offset from GMT for the unit.

set TimeZone [[EST CST MST PST] [+/-HH:MM]] get TimeZone

Username

Specifies the username used for all sessions: NDMP, Telnet, FTP and Webserver. Username is case insensitive, 1 to 32 characters, and cannot contain spaces.

Default: root

set Username [username] get Username

VerboseMode

Controls the level of detail in CLI Help output and command response output for the current CLI session.

Default: enabled

set VerboseMode [enabled disabled] get VerboseMode

VirtualDriveInfo

Displays characteristics and statistics for all the available virtual drives or any available virtual drive identified by its virtual drive ID.

VirtualDriveInfo <VirtualDrive ID>

Voltage

Displays the voltage levels monitored by the FastStream.

Representations of the voltages are VDDA: +3.31 V

VDDB: +2.49 V

VDDC: +1.5V

VDDD: +1.35V

ALL: all monitored voltages

get Voltage <VDDA VDDB VDDC VDDD all>

WrapEventLog

When enabled, the FastStream logs up to 2,048 event entries before wrapping (overwriting the first entries). If disabled, the FastStream stops logging event entries when the buffer is full.

Default: enabled

set WrapEventLog [enabled disabled] get WrapEventLog

zModem

Uses the zMODEM protocol to transfer a file to or from the unit via the RS-232 port. The filename to retrieve is required if the send option is specified.

Zmodem [send [filename] receive]

xviii Appendix

Page 46 Page 48
Image 47
Page 46 Page 48
Contents FastStream VT Page Page Contents Interface options Update storage and firmwareAppendix E Warranty, contact information Xxi Modify storageManagement and control features Hardware featuresVirtual Tape features Backup and restore featuresGbE network Gb FC Switch GbE SwitchEthernet Fibre Channel Physical attributes Installation Install Windows drivers InstallationUnpack the packing box verify contents Install the FastStreamClick on Launch Browser Begin initial configurationConfigure Virtual Tape Use custom initial setup Use quick initial configurationClick on the Add/Remove Hot Spares button Use Hot Spare devicesMove Virtual Tape Cartridges Click in the Enable/Disable Write Protection buttonEnable/Disable Write Protection page appears Secure data through Write ProtectionOptional changes to system parameters Customize the username, passwordChange system configurations Advanced CLI Changes to other parameters may be made using the AdvancedMonitor VTL Monitor storage and diagnose configurationsPhone home E-mail messages Configuration DisplayHealth and Status Monitor Measure drive performance Click the Set up Error Notification buttonConfiguration Select Verify Only Scan drive surfacesVerify storage Click the Initialize and Verify buttonAdd drives to a RAID Group Modify storageInitialize and verify drives Select the Add/Remove Hot Spares button Rebuild RAID GroupsAdd or remove Hot Spares Select Rebuild RAID GroupsClick in the Delete Virtual Tape Library button Add a VTL from another FastStream VTLDelete a VTL Move Virtual Tape Cartridges Preliminary steps Update storage and firmwareRemove stale VTL configuration data Update firmwareClick Send File Use FTP over EthernetUse the RS-232 serial link Send FileType FastStream VT 5300 in the New Connection dialog box Interface optionsUse the serial port Enter Use TelnetCable types Appendix a CablingScsi cabling Cable length Fibre Channel connectionsDisk Appendix B Designing RAID groupsJbod Just a Bunch of Disks RAID LevelIv Appendix Appendix C CLI provides an ASCII-based interface Symbol IndicatesMp1 CLI error messagesCLI summary Command Default ExampleViii Appendix Sntp CLI command explanations DumpConfig DefaultInterleaveDHCPFixedDelay DriveTestConfigEmailUsername EmailPasswordEmailNotifyAddress EmailServerAddressFCHardAddress FCPortErrorsFCDataRate FCHardIsReserved PasswordIPGateway IPSubnetMaskRGCancelAddStorage RAIDCommandTimeoutResetFCPortErrors RestoreConfigurationRGHaltRebuild RGWaitTimeoutRGDisplay RGHaltConversionRMStatus SaveConfigurationSCSIPortReset SCSIPortResetOnStartupTailEventLog SerialPortBaudRateSerialPortEcho SNTPServerThis equipment generates, uses, and can radiate radio Further results of FCC TestingAppendix D Standards and compliances Declaration of Conformity European StandardsContact Atto Technology, Inc Appendix E Warranty, contact informationManufacturer limited warranty Xxii Appendix
Top Page Image Contents