ATTO Technology 5300 Appendix D Standards and compliances, Further results of FCC Testing

Page 48

Appendix D Standards and compliances

The equipment described in this manual generates and uses radio frequency energy. If this equipment is not used in strict accordance with the manufacturer's instruction, it can and may cause interference with radio and television reception. See the ATTO FastStream VT 5300 Technical Specification sheet for your particular model for a full list of certifications for that model.

FCC Standards: Radio and Television

Interference

WARNING

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class B computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide a reasonable protection against such interference when operating in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference.

If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, try to correct the interference by one or more of the following measures:

•Move the receiving antenna.

•Relocate the FastStream VT 5300 with respect to the receiver, or move the FastStream VT 5300 away from the receiver.

•Plug the computer into a different outlet so the computer and receiver are on different branch circuits.

•If necessary, consult an ATTO authorized dealer, ATTO Technical Support Staff, or an experienced radio/television technician for additional suggestions.

The booklet How to Identify and Resolve Radio/TV Interference Problems prepared by the Federal Communications Commission is a helpful guide. It is available from the US Government printing office, Washington, DC 20402, Stock No. 004-000-00345-4.

Further results of FCC Testing

In certain instances, extraordinary variances in the AC power supplied to this unit will require the operating system's normal error recovery procedure to retry the current SCSI command. In this case, the unit can fully recover with no loss of data, and without user intervention. Note that other exceptional conditions in addition to variances in the AC power, such as improper cabling or unrecognized commands, may also trigger these normal error recovery procedures.

Canadian Standards

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

xix

ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual

Page 47 Page 49
Image 48
Page 47 Page 49
Contents FastStream VT Page Page Contents Update storage and firmware Appendix E Warranty, contact information XxiModify storage Interface optionsHardware features Virtual Tape featuresBackup and restore features Management and control featuresGb FC Switch GbE Switch Ethernet Fibre ChannelGbE network Physical attributes Installation Installation Unpack the packing box verify contentsInstall the FastStream Install Windows driversBegin initial configuration Click on Launch BrowserConfigure Virtual Tape Use quick initial configuration Use custom initial setupUse Hot Spare devices Click on the Add/Remove Hot Spares buttonClick in the Enable/Disable Write Protection button Enable/Disable Write Protection page appearsSecure data through Write Protection Move Virtual Tape CartridgesCustomize the username, password Change system configurationsOptional changes to system parameters Changes to other parameters may be made using the Advanced Advanced CLIMonitor storage and diagnose configurations Monitor VTLConfiguration Display Health and Status MonitorPhone home E-mail messages Click the Set up Error Notification button ConfigurationMeasure drive performance Scan drive surfaces Verify storageClick the Initialize and Verify button Select Verify OnlyModify storage Initialize and verify drivesAdd drives to a RAID Group Rebuild RAID Groups Add or remove Hot SparesSelect Rebuild RAID Groups Select the Add/Remove Hot Spares buttonAdd a VTL from another FastStream VTL Delete a VTLClick in the Delete Virtual Tape Library button Move Virtual Tape Cartridges Update storage and firmware Remove stale VTL configuration dataUpdate firmware Preliminary stepsUse FTP over Ethernet Use the RS-232 serial linkSend File Click Send FileInterface options Use the serial portType FastStream VT 5300 in the New Connection dialog box Use Telnet EnterAppendix a Cabling Scsi cablingCable types Fibre Channel connections Cable lengthAppendix B Designing RAID groups Jbod Just a Bunch of DisksRAID Level DiskIv Appendix Symbol Indicates Appendix C CLI provides an ASCII-based interfaceCLI error messages Mp1Command Default Example CLI summaryViii Appendix Sntp CLI command explanations DefaultInterleave DHCPFixedDelayDriveTestConfig DumpConfigEmailPassword EmailNotifyAddressEmailServerAddress EmailUsernameFCPortErrors FCDataRateFCHard FCHardAddressPassword IPGatewayIPSubnetMask IsReservedRAIDCommandTimeout ResetFCPortErrorsRestoreConfiguration RGCancelAddStorageRGWaitTimeout RGDisplayRGHaltConversion RGHaltRebuildSaveConfiguration SCSIPortResetSCSIPortResetOnStartup RMStatusSerialPortBaudRate SerialPortEchoSNTPServer TailEventLogFurther results of FCC Testing Appendix D Standards and compliancesThis equipment generates, uses, and can radiate radio European Standards Declaration of ConformityAppendix E Warranty, contact information Manufacturer limited warrantyContact Atto Technology, Inc Xxii Appendix
Top Page Image Contents