ATTO Technology 5300 RMStatus, RouteDisplay, SaveConfiguration, SCSIInitID, SCSIPortBusSpeed

Page 46

RMStatus

Displays the status of all RAID Members within the specified RAID Group or a specific RAID member (if specified) within the specified RAID Group. This command fails if the specified RAID Group does not exist or a specified member index within the RAID Group does not exist.

RMStatus [GroupName] <MemberIndex>

Route

Assigns a SCSI LUN protocol address to a target. Use the Delete identifier to remove the map. In verbose mode, overwriting a map requires secondary confirmation of the action.

Route FC [lun] [ [RAID [GroupName] Delete ]

RouteDisplay

Displays a list of Fibre Channel to SCSI address mappings on the FastStream.

RouteDisplay FC <fp> <fl>

SaveConfiguration

Issued with the restart option, cycles unit power after saving configuration changes. The norestart option saves changes without restarting.

Note

Certain modifications require a system restart.

SaveConfiguration <Restart NoRestart>

SCSIInitID

Specifies or reports the SCSI initiator ID on the specified SCSI port as found in NVRAM. All maps coinciding with the user-specified SCSIInitID are destroyed after the command is issued.

Default: 7

set SCSIInitID [sb [0-15] ] get SCSIInitID

SCSIPortBusSpeed

Controls the transfer rate at which the unit attempts to negotiate with its SCSI devices.

Default: ultra320

set SCSIPortBusSpeed [sb] [fast ultra ultra2 ultra160 ultra320]

get SCSIPortBusSpeed [sb]

SCSIPortList

Returns a list of available SCSI ports and their current status. Valid status values are OK and Failed

SCSIPortList

xvii

SCSIPortReset

Resets the specified SCSI bus.

SCSIPortReset [sb]

SCSIPortResetOnStartup

Specifies if the SCSI port should be reset on power-up.

Default: enabled

set SCSIPortResetOnStartup [sb [enabled disabled] ]

Requires a SaveConfiguration command get SCSIPortResetOnStartup [sb]

SCSIPortSyncTransfer

Specifies whether synchronous SCSI transfers should be negotiated with devices on the specified SCSI port.

Default: enabled

set SCSIPortSyncTransfer [[sb [enabled disabled] ]

Requires a SaveConfiguration command

get SCSIPortSyncTransfer [sb]

SCSIPortTermination

Configures/reports the SCSI internal termination of the SCSI port identified on the FastStream.

Default: enabled

set SCSIPortTermination [sb] [enabled disabled] Requires a SaveConfiguration command

get SCSIPortTermination [sb]

SCSIPortWideTransfer

Specifies whether wide SCSI transfers should be negotiated. Enabled allows wide transfer negotiation

Default: enabled

set SCSIPortWideTransfer [sb [enabled disabled ]] Requires a SaveConfiguration command

get SCSIPortWideTransfer

SCSITargetLUNs

Sets the maximum number of SCSI LUNs per target the FastStream tries to query during a SCSI bus scan.

Default: 8

set SCSITargetLUNs [sb] [8 64] Requires a SaveConfiguration command get SCSITargetLUNs

SCSITargets

Returns a list of SCSI devices operational on the referenced SCSI port with SCSI target number, SCSI LUN number, device type, vendor ID, product ID, revision and serial number.

SCSITargets [sb]

SerialNumber

Reports the FastStream serial number which is unique for each FastStream. The serial number tracks the board throughout its life and should not be changed.

get SerialNumber

ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual

Page 45 Page 47
Image 46
Page 45 Page 47
Contents FastStream VT Page Page Contents Modify storage Update storage and firmwareAppendix E Warranty, contact information Xxi Interface optionsBackup and restore features Hardware featuresVirtual Tape features Management and control featuresEthernet Fibre Channel Gb FC Switch GbE SwitchGbE network Physical attributes Installation Install the FastStream InstallationUnpack the packing box verify contents Install Windows driversBegin initial configuration Click on Launch BrowserConfigure Virtual Tape Use quick initial configuration Use custom initial setupUse Hot Spare devices Click on the Add/Remove Hot Spares buttonSecure data through Write Protection Click in the Enable/Disable Write Protection buttonEnable/Disable Write Protection page appears Move Virtual Tape CartridgesChange system configurations Customize the username, passwordOptional changes to system parameters Changes to other parameters may be made using the Advanced Advanced CLIMonitor storage and diagnose configurations Monitor VTLHealth and Status Monitor Configuration DisplayPhone home E-mail messages Configuration Click the Set up Error Notification buttonMeasure drive performance Click the Initialize and Verify button Scan drive surfacesVerify storage Select Verify OnlyInitialize and verify drives Modify storageAdd drives to a RAID Group Select Rebuild RAID Groups Rebuild RAID GroupsAdd or remove Hot Spares Select the Add/Remove Hot Spares buttonDelete a VTL Add a VTL from another FastStream VTLClick in the Delete Virtual Tape Library button Move Virtual Tape Cartridges Update firmware Update storage and firmwareRemove stale VTL configuration data Preliminary stepsSend File Use FTP over EthernetUse the RS-232 serial link Click Send FileUse the serial port Interface optionsType FastStream VT 5300 in the New Connection dialog box Use Telnet EnterScsi cabling Appendix a CablingCable types Fibre Channel connections Cable lengthRAID Level Appendix B Designing RAID groupsJbod Just a Bunch of Disks DiskIv Appendix Symbol Indicates Appendix C CLI provides an ASCII-based interfaceCLI error messages Mp1Command Default Example CLI summaryViii Appendix Sntp CLI command explanations DriveTestConfig DefaultInterleaveDHCPFixedDelay DumpConfigEmailServerAddress EmailPasswordEmailNotifyAddress EmailUsernameFCHard FCPortErrorsFCDataRate FCHardAddressIPSubnetMask PasswordIPGateway IsReservedRestoreConfiguration RAIDCommandTimeoutResetFCPortErrors RGCancelAddStorageRGHaltConversion RGWaitTimeoutRGDisplay RGHaltRebuildSCSIPortResetOnStartup SaveConfigurationSCSIPortReset RMStatusSNTPServer SerialPortBaudRateSerialPortEcho TailEventLogAppendix D Standards and compliances Further results of FCC TestingThis equipment generates, uses, and can radiate radio European Standards Declaration of ConformityManufacturer limited warranty Appendix E Warranty, contact informationContact Atto Technology, Inc Xxii Appendix
Top Page Image Contents