ATTO Technology FastStream VT, 5300 operation manual CLI command explanations

Page 39

Command

Default

Example

 

 

 

Voltage

 

get voltage

 

 

 

WrapEventLog

enabled

set wrapeventlog disabled

 

 

 

zModem

 

zmodem receive

 

 

 

CLI command explanations

Command Line Interface commands are listed alphabetically with explanations of what they are used for, their defaults and syntax.

CAUTION

Do not use CLI unless you are directed to by an ATTO technician.

Changing parameters may cause loss of data and/or disruption to performance and reliability of the FastStream.

The FastStream VT 5300 GUI is the preferred method to operate and manage the FastStream VT 5300. Refer to Interface options on page 23 for details

AutoMap

Automap automatically maps a subset of target devices visible to the firmware. All previous maps are deleted.

AutoMap

AutoResume

Enables/disables the automatic continue feature for interrupted rebuild, erase and write pattern operations at startup. If AutoResume is enabled, all interrupted rebuild, erase and write pattern operations are continued at startup. Optional parameter GroupName specifies the RAID Group whose Restart features to be set. If no GroupName is specified, all existing RAID Groups are affected.

Default: all disabled

set AutoResume [Rebuild Erase WritePattern all] [enabled disabled] <GroupName>

BlockDevClean

Removes any ATTO configuration data from the block device with the specified BlockDevID. BlockDevID is the index of a block device provided by the BlockDevScan CLI command.

BlockDevClean [BlockDevID]

Date

Regulates the current date for this unit. The date range is 1/1/2000 to 12/31/2099.

BlockDevIdentify

Causes the I/O LED of the drive to illuminate for one minute if it is accessible through the SCSI port

CAUTION

The BlockDevIdentify command is intended for diagnostic purposes only. Executing this command may adversely impact the performance and throughput of the FastStream for the time that the LED is illuminated.

BlockDevIdentify <Groupname> [BlockDevID MberIdx]

BlockDevIDStop

Turns off the IO LED of a previously identified disk drive.

BlockDevIDStop

BlockDevScan

Lists all currently connected physical drives along with any potential RAID Group association. Each block device listed is assigned a unique index at the time of the scan to identify drives for other CLI operations.

BlockDevScan

BridgeModel

Reports model information about the FastStream.

get BridgeModel

BridgeName

Specifies the eight-character name assigned to the FastStream used to identify individual FastStream units. It is not the World Wide Name. The string is alphanumeric, eight characters long,.

Default: ““

set BridgeName [value]

Requires a SaveConfiguration command get BridgeName

ClearEventLog

Clears the contents of the event log. No new entries are recorded until ClearEventLog has completed.

ClearEventLog

Default: 01/01/2000

set Date [MM] [DD] [YYYY] get Date

x Appendix

Page 38 Page 40
Image 39
Page 38 Page 40
Contents FastStream VT Page Page Contents Interface options Update storage and firmwareAppendix E Warranty, contact information Xxi Modify storageManagement and control features Hardware featuresVirtual Tape features Backup and restore featuresGb FC Switch GbE Switch Ethernet Fibre ChannelGbE network Physical attributes Installation Install Windows drivers InstallationUnpack the packing box verify contents Install the FastStreamClick on Launch Browser Begin initial configurationConfigure Virtual Tape Use custom initial setup Use quick initial configurationClick on the Add/Remove Hot Spares button Use Hot Spare devicesMove Virtual Tape Cartridges Click in the Enable/Disable Write Protection buttonEnable/Disable Write Protection page appears Secure data through Write ProtectionCustomize the username, password Change system configurationsOptional changes to system parameters Advanced CLI Changes to other parameters may be made using the AdvancedMonitor VTL Monitor storage and diagnose configurationsConfiguration Display Health and Status MonitorPhone home E-mail messages Click the Set up Error Notification button ConfigurationMeasure drive performance Select Verify Only Scan drive surfacesVerify storage Click the Initialize and Verify buttonModify storage Initialize and verify drivesAdd drives to a RAID Group Select the Add/Remove Hot Spares button Rebuild RAID GroupsAdd or remove Hot Spares Select Rebuild RAID GroupsAdd a VTL from another FastStream VTL Delete a VTLClick in the Delete Virtual Tape Library button Move Virtual Tape Cartridges Preliminary steps Update storage and firmwareRemove stale VTL configuration data Update firmwareClick Send File Use FTP over EthernetUse the RS-232 serial link Send FileInterface options Use the serial portType FastStream VT 5300 in the New Connection dialog box Enter Use TelnetAppendix a Cabling Scsi cablingCable types Cable length Fibre Channel connectionsDisk Appendix B Designing RAID groupsJbod Just a Bunch of Disks RAID LevelIv Appendix Appendix C CLI provides an ASCII-based interface Symbol IndicatesMp1 CLI error messagesCLI summary Command Default ExampleViii Appendix Sntp CLI command explanations DumpConfig DefaultInterleaveDHCPFixedDelay DriveTestConfigEmailUsername EmailPasswordEmailNotifyAddress EmailServerAddressFCHardAddress FCPortErrorsFCDataRate FCHardIsReserved PasswordIPGateway IPSubnetMaskRGCancelAddStorage RAIDCommandTimeoutResetFCPortErrors RestoreConfigurationRGHaltRebuild RGWaitTimeoutRGDisplay RGHaltConversionRMStatus SaveConfigurationSCSIPortReset SCSIPortResetOnStartupTailEventLog SerialPortBaudRateSerialPortEcho SNTPServerFurther results of FCC Testing Appendix D Standards and compliancesThis equipment generates, uses, and can radiate radio Declaration of Conformity European StandardsAppendix E Warranty, contact information Manufacturer limited warrantyContact Atto Technology, Inc Xxii Appendix
Top Page Image Contents