ATTO Technology FastStream VT, 5300 operation manual Use Telnet, Enter

Page 29

Note

In serial port sessions, there is no prompt on the line below the word Ready. Begin typing commands in the blank line where the cursor is resting. No username or password is required for serial port access.

5To verify that you have connected successfully, type help after the Ready prompt and press

Enter.

Use Telnet

Up to three Telnet sessions can be conducted simultaneously. A serial port session can use the CLI while Telnet sessions are open. Whichever session issues the first “set” CLI command can continue to issue set commands, while the other sessions can only issue “get” commands or display information. Once a connection is established, refer to CLI provides an ASCII- based interface on page v of the Appendix..

1Connect to the FastStream VT 5300 from a computer on the same Ethernet network.

2Start a Telnet session.

Note

There is more than one way to connect to the FastStream VT 5300 using a telnet

If a list of all available commands does not appear on the screen, review the steps in this section, check the cable, or contact service personnel until the problem is solved.

If you have difficulty using the serial port, verify that you have the correct settings and that your serial cable is less then two meters long.

program.Your telnet program may operate differently than in the following instructions.

3At the telnet prompt, issue the open command where x.x.x.x is the IP address of the FastStream VT 5300.

telnet > open x.x.x.x

4If you have to specify a port type, type in the port type “telnet” and the terminal type “vt100”.

port type: telnet

terminal type: vt100

5Type in the default values for the username, “root”, and the password, “Password”, if you did not set new values in Discover the IP address on page 5.

24

Image 29

Contents FastStream VT Page Page Contents Appendix E Warranty, contact information Xxi Update storage and firmwareModify storage Interface optionsVirtual Tape features Hardware featuresBackup and restore features Management and control featuresGbE network Gb FC Switch GbE SwitchEthernet Fibre Channel Physical attributes Installation Unpack the packing box verify contents InstallationInstall the FastStream Install Windows driversClick on Launch Browser Begin initial configurationConfigure Virtual Tape Use custom initial setup Use quick initial configurationClick on the Add/Remove Hot Spares button Use Hot Spare devicesEnable/Disable Write Protection page appears Click in the Enable/Disable Write Protection buttonSecure data through Write Protection Move Virtual Tape CartridgesOptional changes to system parameters Customize the username, passwordChange system configurations Advanced CLI Changes to other parameters may be made using the AdvancedMonitor VTL Monitor storage and diagnose configurationsPhone home E-mail messages Configuration DisplayHealth and Status Monitor Measure drive performance Click the Set up Error Notification buttonConfiguration Verify storage Scan drive surfacesClick the Initialize and Verify button Select Verify OnlyAdd drives to a RAID Group Modify storageInitialize and verify drives Add or remove Hot Spares Rebuild RAID GroupsSelect Rebuild RAID Groups Select the Add/Remove Hot Spares buttonClick in the Delete Virtual Tape Library button Add a VTL from another FastStream VTLDelete a VTL Move Virtual Tape Cartridges Remove stale VTL configuration data Update storage and firmwareUpdate firmware Preliminary stepsUse the RS-232 serial link Use FTP over EthernetSend File Click Send FileType FastStream VT 5300 in the New Connection dialog box Interface optionsUse the serial port Enter Use TelnetCable types Appendix a CablingScsi cabling Cable length Fibre Channel connectionsJbod Just a Bunch of Disks Appendix B Designing RAID groupsRAID Level DiskIv Appendix Appendix C CLI provides an ASCII-based interface Symbol IndicatesMp1 CLI error messagesCLI summary Command Default ExampleViii Appendix Sntp CLI command explanations DHCPFixedDelay DefaultInterleaveDriveTestConfig DumpConfigEmailNotifyAddress EmailPasswordEmailServerAddress EmailUsernameFCDataRate FCPortErrorsFCHard FCHardAddressIPGateway PasswordIPSubnetMask IsReservedResetFCPortErrors RAIDCommandTimeoutRestoreConfiguration RGCancelAddStorageRGDisplay RGWaitTimeoutRGHaltConversion RGHaltRebuildSCSIPortReset SaveConfigurationSCSIPortResetOnStartup RMStatusSerialPortEcho SerialPortBaudRateSNTPServer TailEventLogThis equipment generates, uses, and can radiate radio Further results of FCC TestingAppendix D Standards and compliances Declaration of Conformity European StandardsContact Atto Technology, Inc Appendix E Warranty, contact informationManufacturer limited warranty Xxii Appendix