ATTO Technology FastStream VT EmailNotifyAddress, EmailPassword, EmailServerAddress, EthernetMDIX

Page 41

EmailNotifyAddress

Configures notification addresses using an index (a number between 1 and 5, inclusive), the full E-mail address of the recipient, a fully qualified Internet E-mail address not more than 128 characters long, and a level.

Levels are

None: no E-mails sent.

Critical: critical event notification.

Warning: warnings and critical event notification.

All: all warnings, critical events

set EmailNotifyAddress [index] [full email address] [warning level]

get EMailNotifyAddress

EmailPassword

Configures the password used to authenticate the login to the SMTP email server. The password must not be more than 64 characters. A password is not required if the email server does not require authentication.

set EmailPassword

EmailServerAddress

Configures the address of the server that the FastStream should contact in order to send E-mails.

Default: 0.0.0.0

set EmailServerAddress [IP address] get EmailServerAddress

EmailUsername

Configures the username used to authenticate the login to the SMTP email server. The username must not be more than 128 characters. A username is not required if the email server does not require authentication.

set EmailUsername [Username] get EmailUsername

EthernetMDIX

Specifies the Ethernet twisted-pair connection type.

The MDI setting connects the unit's Ethernet port to an Ethernet hub or switch port with a standard Ethernet patch cable (or to a PCI card with a cross-over cable).

The MDIX setting connects the unit's Ethernet port to an Ethernet PCI card with a standard Ethernet patch cable (or to a hub or switch with a cross-over cable).

The Auto setting attempts to automatically determine the correct setting.

Default: MDI

set EthernetMDIX [mp1] [MDI MDIX auto] get EthernetMDIX [mp1]

EthernetSpeed

Sets/displays the current speed of the Ethernet connection. Choices are 10, 100, and Auto.

Default: auto

set EthernetSpeed [mp1] [ 10 100 Auto ] Requires a SaveConfiguration command get EthernetSpeed [mp1]

EventLog

When enabled, records various system errors to the event log.

Default: enabled

set EventLog [enabled disabled] get EventLog

EventLogFilter

Filters data from specific unit subsystems and levels when event logging is enabled. The specific entries supported are platform-dependent.

Subsystem

Levels

ECC

INFO

ENET

WARN

GEN

CRIT

HTTP

FAIL

NVRAM

ALL

PERF

 

SCSI

 

NDMP

 

FC

 

ALL

 

set EventLogFilter [subsys all] [event level all] [all none]

get EventLogFilter [subsystem] [level]

Exit

Exits the current Ethernet telnet CLI session; it has no effect if used during a serial or in-band CLI session.

Exit

FCConnMode

Controls/reports the connection mode the FastStream uses when communication across a FC network, either to an arbitrated loop (FC-AL) when you select loop mode, or point-to-point when you choose ptp. If you choose loop-ptpor ptp-loop, the FastStream tries to use the first parameter first.

Default: loop

set FCConnMode [fp] [loop ptp loop-ptp ptp-loop] Requires a SaveConfiguration command

get FCConnMode [fp]

xii Appendix

Page 40 Page 42
Image 41
Page 40 Page 42
Contents FastStream VT Page Page Contents Appendix E Warranty, contact information Xxi Update storage and firmwareModify storage Interface optionsVirtual Tape features Hardware featuresBackup and restore features Management and control featuresGbE network Gb FC Switch GbE SwitchEthernet Fibre Channel Physical attributes Installation Unpack the packing box verify contents InstallationInstall the FastStream Install Windows driversClick on Launch Browser Begin initial configurationConfigure Virtual Tape Use custom initial setup Use quick initial configurationClick on the Add/Remove Hot Spares button Use Hot Spare devicesEnable/Disable Write Protection page appears Click in the Enable/Disable Write Protection buttonSecure data through Write Protection Move Virtual Tape CartridgesOptional changes to system parameters Customize the username, passwordChange system configurations Advanced CLI Changes to other parameters may be made using the AdvancedMonitor VTL Monitor storage and diagnose configurationsPhone home E-mail messages Configuration DisplayHealth and Status Monitor Measure drive performance Click the Set up Error Notification buttonConfiguration Verify storage Scan drive surfacesClick the Initialize and Verify button Select Verify OnlyAdd drives to a RAID Group Modify storageInitialize and verify drives Add or remove Hot Spares Rebuild RAID GroupsSelect Rebuild RAID Groups Select the Add/Remove Hot Spares buttonClick in the Delete Virtual Tape Library button Add a VTL from another FastStream VTLDelete a VTL Move Virtual Tape Cartridges Remove stale VTL configuration data Update storage and firmwareUpdate firmware Preliminary stepsUse the RS-232 serial link Use FTP over EthernetSend File Click Send FileType FastStream VT 5300 in the New Connection dialog box Interface optionsUse the serial port Enter Use TelnetCable types Appendix a CablingScsi cabling Cable length Fibre Channel connectionsJbod Just a Bunch of Disks Appendix B Designing RAID groupsRAID Level DiskIv Appendix Appendix C CLI provides an ASCII-based interface Symbol IndicatesMp1 CLI error messagesCLI summary Command Default ExampleViii Appendix Sntp CLI command explanations DHCPFixedDelay DefaultInterleaveDriveTestConfig DumpConfigEmailNotifyAddress EmailPasswordEmailServerAddress EmailUsernameFCDataRate FCPortErrorsFCHard FCHardAddressIPGateway PasswordIPSubnetMask IsReservedResetFCPortErrors RAIDCommandTimeoutRestoreConfiguration RGCancelAddStorageRGDisplay RGWaitTimeoutRGHaltConversion RGHaltRebuildSCSIPortReset SaveConfigurationSCSIPortResetOnStartup RMStatusSerialPortEcho SerialPortBaudRateSNTPServer TailEventLogThis equipment generates, uses, and can radiate radio Further results of FCC TestingAppendix D Standards and compliances Declaration of Conformity European StandardsContact Atto Technology, Inc Appendix E Warranty, contact informationManufacturer limited warranty Xxii Appendix
Top Page Image Contents