ATTO Technology FastStream VT, 5300 Scan drive surfaces, Verify storage, Select Verify Only

Page 21

Scan drive surfaces

The read only test performs a non-destructive scan over the entire surface of each drive to identify bad areas of the disk drives and determine read performance. It may be run while data is passing through the FastStream.

Running this test may negatively impact performance. Once the Read-only test has completed, system operation returns to normal.

1If you are not already in the FastStream GUI, type the IP address of your appliance, as found

in Use the FastStream VT 5300 GUI on page

23, in a standard browser, click Enter Here and type in your username and password.

2The Monitor VTL page appears. On the menu at the left hand side of the page, click on Diagnostics.

3The Diagnostics Menu page appears.

4Click the Read-Only Drive test button

5Click Next

6Choose the drives you wish to test

7Click Commit

8A warning message displays; choose yes to continue.

9The Drive Performance and Health screen appears with the Drive Metrics box displaying basic information about the drives. Click on the Show Help Text and Drives arrow.

10If a drive is being read, its display shows the percentage of progress. When the test is complete, click on each drive to see its information highlighted in the Drive Metrics window.

Note

If you close the browser or navigate away from this page, you may re-access these results by clicking the Diagnostics button and choosing the Drive Performance and Health option. Results are available until the FastStream is restarted.

Verify storage

Verify the status of attached storage to identify drive issues after drives have been initialized. If the verify operation detects an error, the FastStream tries to re initialize the drive, erasing information stored on the drive. Be sure to back up data before performing verification.

CAUTION

Data may be erased during this process. Back up your data before selecting Commit.

These operations have a negative impact on the performance of normal operations; all activity should be stopped.

1If you are not already in the FastStream GUI, type the IP address of your appliance, as found

in Use the FastStream VT 5300 GUI on page

23, in a standard browser, click Enter Here and type in your username and password.

2The Monitor VTL page appears. On the menu at the left hand side of the page, click on Diagnostics.

3The Diagnostics Menu page appears.

4Click the Initialize and Verify button

5Click Next

6Click on the drives you wish to test; the drives are highlighted.

7Select Verify Only

8Click Commit

9A warning message displays; choose yes to continue.

10The Drive Performance and Health screen appears

11The Time Remaining box tells you how much time remains until the verification process is complete. The representation of each drive in the Drives box shows the percentage of verification completed.

16

Image 21
Contents FastStream VT Page Page Contents Appendix E Warranty, contact information Xxi Update storage and firmwareModify storage Interface optionsVirtual Tape features Hardware featuresBackup and restore features Management and control featuresGb FC Switch GbE Switch Ethernet Fibre ChannelGbE network Physical attributes Installation Unpack the packing box verify contents InstallationInstall the FastStream Install Windows driversClick on Launch Browser Begin initial configurationConfigure Virtual Tape Use custom initial setup Use quick initial configurationClick on the Add/Remove Hot Spares button Use Hot Spare devicesEnable/Disable Write Protection page appears Click in the Enable/Disable Write Protection buttonSecure data through Write Protection Move Virtual Tape CartridgesCustomize the username, password Change system configurationsOptional changes to system parameters Advanced CLI Changes to other parameters may be made using the AdvancedMonitor VTL Monitor storage and diagnose configurationsConfiguration Display Health and Status MonitorPhone home E-mail messages Click the Set up Error Notification button ConfigurationMeasure drive performance Verify storage Scan drive surfacesClick the Initialize and Verify button Select Verify OnlyModify storage Initialize and verify drivesAdd drives to a RAID Group Add or remove Hot Spares Rebuild RAID GroupsSelect Rebuild RAID Groups Select the Add/Remove Hot Spares buttonAdd a VTL from another FastStream VTL Delete a VTLClick in the Delete Virtual Tape Library button Move Virtual Tape Cartridges Remove stale VTL configuration data Update storage and firmwareUpdate firmware Preliminary stepsUse the RS-232 serial link Use FTP over EthernetSend File Click Send FileInterface options Use the serial portType FastStream VT 5300 in the New Connection dialog box Enter Use TelnetAppendix a Cabling Scsi cablingCable types Cable length Fibre Channel connectionsJbod Just a Bunch of Disks Appendix B Designing RAID groupsRAID Level DiskIv Appendix Appendix C CLI provides an ASCII-based interface Symbol IndicatesMp1 CLI error messagesCLI summary Command Default ExampleViii Appendix Sntp CLI command explanations DHCPFixedDelay DefaultInterleaveDriveTestConfig DumpConfigEmailNotifyAddress EmailPasswordEmailServerAddress EmailUsernameFCDataRate FCPortErrorsFCHard FCHardAddressIPGateway PasswordIPSubnetMask IsReservedResetFCPortErrors RAIDCommandTimeoutRestoreConfiguration RGCancelAddStorageRGDisplay RGWaitTimeoutRGHaltConversion RGHaltRebuildSCSIPortReset SaveConfigurationSCSIPortResetOnStartup RMStatusSerialPortEcho SerialPortBaudRateSNTPServer TailEventLogFurther results of FCC Testing Appendix D Standards and compliancesThis equipment generates, uses, and can radiate radio Declaration of Conformity European StandardsAppendix E Warranty, contact information Manufacturer limited warrantyContact Atto Technology, Inc Xxii Appendix