ATTO Technology FastStream VT, 5300 Health and Status Monitor, Configuration Display

Page 19

Health and Status Monitor page

1If you are not already in the FastStream GUI, type the IP address of your appliance, as found

in Use the FastStream VT 5300 GUI on page

23, in a standard browser, click Enter Here and type in your username and password.

2The Monitor VTL page appears. On the menu at the left hand side of the page, click on Diagnostics.

3The Health and Status Monitor page appears. If you click Details, added information about each parameter appears on the Configuration

Display page (refer to Configuration Display

page below).

•RAID Groups

RAID Group names, RAID status, available Hot Spares and number of faulted drives

•Environmental Status Temperature and voltage

•Interface Status

Ethernet management port link status and Fibre Channel port link, speed and connection mode

•Drive status by port Size and status

Configuration Display page

Clicking on Details in the Health and Status Monitor page (refer to details above) gives you added information about each parameter on the Configuration Display page. You may view the details of any parameter from this page.

•RAID Groups

RAID Group names, RAID status, available Hot Spares, number of faulted drives, RAID Level, Interleave and total capacity of each RAID Group.

•Drives

Drive Configuration by port, including drive size and status

•Interfaces

Ethernet management port link status and Fibre Channel port link, speed, connection mode, Node Name and Port Name.

Note

At any point, if you do not want to continue before you click Commit, click on the Cancel button to return to the previous setup menu.

Phone home: E-mail messages

E-mail notification allows the FastStream VT 5300 to send an E-mail message to you, a network administrator or other users when certain events occur with the FastStream. Serious error messages are sent immediately, while messages for less serious errors are sent every 15 minutes.

•Types of errors

•SCSI device errors such as medium error, aborted command and hard error

•Device transitions from online to offline

•Critical and warning temperature conditions

•Critical and warning voltage conditions

•Power recycle/power failure conditions

•Warning messages

•device down

•medium error

•abort command

•Warning levels

•All: warnings, critical events and informational messages are sent

•Critical: critical event E-mails are sent

•Warning: warnings and critical event E- mails are sent

•None: no E-mails are sent

You may send E-mails to up to five E-mail addresses and designate which conditions prompt each E-mail notification.

For example, a recipient with a critical severity level only receives critical messages and not warning or informational messages.

When an event occurs that warrants E-mail notification, the FastStream VT 5300 sends the

14

Page 18 Page 20
Image 19
Page 18 Page 20
Contents FastStream VT Page Page Contents Interface options Update storage and firmwareAppendix E Warranty, contact information Xxi Modify storageManagement and control features Hardware featuresVirtual Tape features Backup and restore featuresEthernet Fibre Channel Gb FC Switch GbE SwitchGbE network Physical attributes Installation Install Windows drivers InstallationUnpack the packing box verify contents Install the FastStreamClick on Launch Browser Begin initial configurationConfigure Virtual Tape Use custom initial setup Use quick initial configurationClick on the Add/Remove Hot Spares button Use Hot Spare devicesMove Virtual Tape Cartridges Click in the Enable/Disable Write Protection buttonEnable/Disable Write Protection page appears Secure data through Write ProtectionChange system configurations Customize the username, passwordOptional changes to system parameters Advanced CLI Changes to other parameters may be made using the AdvancedMonitor VTL Monitor storage and diagnose configurationsHealth and Status Monitor Configuration DisplayPhone home E-mail messages Configuration Click the Set up Error Notification buttonMeasure drive performance Select Verify Only Scan drive surfacesVerify storage Click the Initialize and Verify buttonInitialize and verify drives Modify storageAdd drives to a RAID Group Select the Add/Remove Hot Spares button Rebuild RAID GroupsAdd or remove Hot Spares Select Rebuild RAID GroupsDelete a VTL Add a VTL from another FastStream VTLClick in the Delete Virtual Tape Library button Move Virtual Tape Cartridges Preliminary steps Update storage and firmwareRemove stale VTL configuration data Update firmwareClick Send File Use FTP over EthernetUse the RS-232 serial link Send FileUse the serial port Interface optionsType FastStream VT 5300 in the New Connection dialog box Enter Use TelnetScsi cabling Appendix a CablingCable types Cable length Fibre Channel connectionsDisk Appendix B Designing RAID groupsJbod Just a Bunch of Disks RAID LevelIv Appendix Appendix C CLI provides an ASCII-based interface Symbol IndicatesMp1 CLI error messagesCLI summary Command Default ExampleViii Appendix Sntp CLI command explanations DumpConfig DefaultInterleaveDHCPFixedDelay DriveTestConfigEmailUsername EmailPasswordEmailNotifyAddress EmailServerAddressFCHardAddress FCPortErrorsFCDataRate FCHardIsReserved PasswordIPGateway IPSubnetMaskRGCancelAddStorage RAIDCommandTimeoutResetFCPortErrors RestoreConfigurationRGHaltRebuild RGWaitTimeoutRGDisplay RGHaltConversionRMStatus SaveConfigurationSCSIPortReset SCSIPortResetOnStartupTailEventLog SerialPortBaudRateSerialPortEcho SNTPServerAppendix D Standards and compliances Further results of FCC TestingThis equipment generates, uses, and can radiate radio Declaration of Conformity European StandardsManufacturer limited warranty Appendix E Warranty, contact informationContact Atto Technology, Inc Xxii Appendix
Top Page Image Contents